505290

General Electric GCG1520 Manual

13
Zoom out
Zoom in
Previous page
1/20
Next page
13
Customer ServiceTroubleshooting Tips
Operating InstructionsSafety Instructions
Installation Instructions
Measure the height of your cabinet opening.
The top of the compactor should be at least
1/8″ (3 mm) from the top of the cabinet
opening.
The rear wheels are preset for a cabinet
opening height of 34-1/4″ (87 cm)
(Position “A”).
To adjust for other cabinet opening heights,
loosen screw just enough to clear stud from
hole in position “A”. Move the rear wheel and
stud to position “B” or “C” as needed for your
cabinet opening measurement:
Position B: 34-1/4″ to 34-7/16″
(87 to 87.5 cm)
Position C: 34-7/16″ to 34-5/8″
(87.5 to 88 cm)
Tighten screw. Repeat for other rear wheel.
5
Use pliers to lower leveling legs away from cabinet. Adjust legs so there will be a 1/8″ (3 mm)
to 1/4″ (6.4 mm) space between the top of the compactor and the top of the cabinet opening.
Stand the compactor upright.
6
Use pliers to lower leveling legs away from
cabinet. Place level inside on the floor of the
cabinet. Check that the compactor is level
from front to back and side to side. Adjust the
leveling legs until the compactor is level.
7
Determine if you want the compactor frame
or drawer front flush with the cabinet front.
Adjust the retaining brackets to the cabinet
top as needed:
If the compactor frame is to be flush with the
cabinet front,
place retaining bracket screws
through “A”.
If the compactor drawer front is to be flush with
the cabinet front,
place retaining bracket
screws through “C”.
If the compactor is to be midway between
“A” and ”C”,
place retaining bracket screws
through “B”.
8
Injury Hazard
WARNING
When moving or lifting the compactor, use a glove to protect and cushion your hand.
More than one person is recommended to lift or move compactor because of its size
and weight. Use proper lifting methods.
Failure to follow these instructions could result in injury.
Cabinet
Countertop
Retaining
bracket
C
B
A
Locating stud
Wheel bracket
assembly
Self-tapping screw (pivot)
A
B
C
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for General Electric GCG1520 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of General Electric GCG1520 in the language / languages: English as an attachment in your email.

The manual is 0,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info