PAGE 8
PAGE 9
PROGRAMMABLE FUNCTIONS
ACOUSTIC SIGNALS
CDL DOUBLE OPENING PULSE
CURRENT ABSORPTION SENSOR
ANTI-DISTRACTION FUNCTION AND DOOR LOCKING
By enabling this function you will obtain, upon deactivation of the system, a
double control pulse on the door-unlocking line (about 0,5 second each).
This allows the opening of the centralized door locks on vehicles having the
diversified door opening (first pulse driver side door opening, second pulse
other doors opening).
This function is active only if the opening/closing time of 0,5” is selected, while
setting the opening/closing time of 6” will automatically disabled the double
pulse.
This function determines the automatic activation of the system if this has been
disarmed and no voluntary actions are performed by the user (e.g. Door
opening).
The function prevents the vehicle from being left unprotected in cases where,
after the arming of the system, this is turned OFF accidentally by pressing the
button Nr.1 of the remote control.
The self rearming is confirmed by the alarm with visual/acoustic signalling (one
flash by the turn signals and one acoustic signal) .
The anti-distraction function activates the CDL control; therefore, in order to
prevent involuntary activations of the system, it's MANDATORY to connect the
door pin switch to the system input (BROWN/GREN wire of the alarm wiring).
This function allows the user to set intermittent sound (horn) or continuos
sound (siren). See the relative paragraph for programming.
The comfort control allows the automatic regulation of window closing, when
the alarm is armed.
In fact, after this function has been activated, at any alarm arming, the window
winder motor/control unit will receive a 25” command, to close the windows.
Together with the previously described function, the automatic door locking of
the vehicle is done when running.
LOCKING TIME
COMFORT CONTROL
ATTENTION: before activating of the absorption sensor, it is suggested
to consult the specific rules being in force in your country (noise
pollution).
NOTE: after disarming, a door opening will stop the function.
The standard locking time of the alarm is set to 0,5”, and if the vehicle needs a
locking time of 6”, you can vary this parameter during the programming phase.
When the comfort function has been activated, let the locking time set
to 0,5”. In fact, if the locking time is set to 6”, when the alarm is disarmed, the
windows of the vehicle will open.
NOTE:
Being closed all the doors of the vehicle, turn the ignition key to “ON”; after 35”,
all doors will be locked.
By turning the ignition key to “OFF”, all doors of the vehicle will be automatically
unlocked.
To prevent this function from being activated accidentally, the system
continuously monitors the status of the ignition key and the input line of the
DOOR and BOOT PUSHBUTTONS and therefore does not allow operation of
the locks if the DOORS and BOOT are opened manually while starting the
engine or during the 20” after starting it.
If enabled, the PANIC ALARM function allows the user to activate the visual
and audio alarm signals deliberately by pressing key 2 on the remote.
This function works regardless of whether the alarm system is “ON” or “OFF”.
The alarm signal lasts up to approx. 30”. However, you can silence it at any
time by pressing key 2 on the remote again
While the alarm signal is emitted the LED emits a continuous light.
Between one panic alarm cycle and the next there is a neutral time of
approximately 5” during which it is not possible to activate the alarm signal
again.
While the alarm signal is given out and during the consequent neutral time, the
LED stays on.
If the PANIC function has been disabled during the programming phase,
pressing key Nr. 2 on the remote will activate the BOOT OPENING function.
On cars having the BOOT OPENING function, you can open the boot
electrically by pressing key Nr. 2 on the remote regardless of whether the alarm
system is ON or OFF.
If you press key Nr. 2 on the remote when the alarm system is DEACTIVATED,
you will open the boot without any signals being given out. If the alarm system
is activated and key Nr. 2 is pressed, the boot will open, the turn indicators will
flash and the fixed light of the status LED will turn on.
When the alarm system is ON, opening the boot will generate a time interval of
approx. 60”, during which protection functions are suspended to allow the
loading / unloading of the goods carried without causing false alarms.After 60”
the status LED will go out to indicate that the normal protection functions of the
alarm system have been resumed.
You can turn off the load/unload function even before the end of the 60” period
by pressing key Nr. 2 on the remote.
In this case the status LED will go out immediately, and the alarm system will
resume its normal protection functions with the appropriate signals.
opening the boot is not allowed during the NEUTRAL ACTIVATION
TIME, because during this time, key Nr. 2 of the remote is used to cut out the
volume sensors and the comfort function.
PANIC ALARM OR CAR-FINDER
NOTE:
