479861

Gemini 7590 Manual

8
Zoom out
Zoom in
Previous page
1/12
Next page
SELF-POWERED ENCODED SIREN 7125TNC
DESCRIPTION
THE SELF-POWERED ELECTRONIC SIREN 7125TNC IS A HIGH-POWERED SOUND SIGNAL LING DEVICE
DESIGNED TO BE INSTALLED IN THE ENGINE COMPARTMENT OF VEHICLES. IT MUST BE CONNECTED TO THE
ALARM CONTROL UNIT BY MEANS OF THE WIRING HARNESS SUPPLIED IN THE KIT.
TO INSTALL THE SIREN, USE THE BRACKET AND SCREWS SUPPLIED WITH IT. FOLLOW THE ASSEMBLY
DIAGRAM. SECURE UNIT TO AN UNYIELDING PART OF THE CAR AT A SUFFICIENT DISTANCE FROM HEAT
SOURCES.
OPERATION
The self-powered electronic siren 7125TNC has an internal self -powering device which guarantees
operation in a power outage or if the wires connecting to the control unit are cut.
By means of the encoded system of communication between alarm and siren, the alarm activates and
deactivates the siren battery charging and self-powering functions.
The internal battery is charged only with the alarm system Off and is interrupted automatically upon
reaching a predetermined charge level.
The self-powering unit, however, is activated only with the alarm system ON and it remains activate for
approximately 3 minutes after alarm deactivation.
Therefore, after deactivating the alarm wait at least three minutes before disconnecting the siren.
CONNECTIONS
Connect the BLACK wire marked with RB to the positive pole of the vehicle battery.
Connect the BLACK wire marked with MB to the negative pole of the vehicle battery.
Connect the BLACK wire marked with L to the BLUE wire from the alarm control unit.
Connect the BLACK wire marked with S to the PINK wire from the alarm control unit.
NB: Before powering the siren, make sure all the connections have been made.
INSTALLATION
Use the bracket and screws supplied with the kit to fit the siren in the engine compartment.
Use an 8 mm wrench to tighten the nuts.
Install the siren at some distance from sources of heat or areas where there might be stagnant water.
Arrange the horn with the opening facing down.
Protect wires from water and humidity by insulating the connection points and using protective
sheaths.
Make sure the rubber casing adheres properly to the siren before fastening the screws.
IF YOU WANT TO WASH THE ENGINE, DO NOT AIM THE WATER JET AT THE SIREN .
ELECTRONIC SIREN 7147
DESCRIPTION
ELECTRONIC SIREN 7147 IS A HIGH -POWER SOUND SIGNALLING DEVICE DESIGNED TO BE INSTALLED IN THE
ENGINE COMPARTMENT. IT IS CONNECTED TO THE ALARM CONTROL UNIT BY MEANS OF TWO WIRES ONLY.
CONNECTIONS
Connect the Red wire to the positive pole of the vehicle battery.
Connect the Black wire to the YELLOW-BLACK wire of the alarm control unit.
ASSEMBLY
Use the bracket and screws supplied with the kit to install the siren in the engine compartment.
Use an 8 mm wrench to tighten the nuts.
Install the siren at some distance from sources of heat or areas where there might be stagnant water.
Arrange the horn with the opening facing down.
IF YOU WANT TO WASH THE ENGINE, DO NOT AIM THE WATER JET AT THE SIREN .
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gemini 7590 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gemini 7590 in the language / languages: English as an attachment in your email.

The manual is 0,36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info