544879

Geba Tronic DC 3 ECO - Standard - de Luxe Manual

6
Zoom out
Zoom in
Previous page
1/18
Next page
316
industrial controls
®
industrial controls
®
Connecting external push-buttons UP, STOP, DOWN
For the use from outside of ther DC 3 an external 3x bushbutton unit (e.g. KDT-3) can be
connected
36
37 44
45
38 39
external push button unit
Connection safety edge (optional, only if Comfort module is connected!)
The controlling of the safety edge is managed by the Comfort module and therefore there is
no need for an additional safety edge controler device. According to the EU regulations it is
necessary to test the pneumatic safety edge on EVERY door cycle, therefore it is possible
to connect a pre-limit switch to the DC 3, which starts the intelligent test procedure (resp.
with an electric safety bar, changes the the function from „STOP with reverse“ to „STOP“).
Connecting an electro mechanical safety edge (optional, only if Comfort modul is connected!)
In order to test the complete circuit of the pneumatic safety edge, it is necessary to connect
(on the inside of the pressure switch enclosure) a resistor (3,3 up 8,2 kΩ) in series with the
normally closed contact of the pressure switch.
Connection of a electro-mechanical safety edge
48
49
P
3,3 bis 8,2 kΩ
Connecting of limit switches
The potentialfree limit switches UP & DOWN are connected to the terminals 30 & 31 (UP)
and 32 & 33 (DOWN).
Connection limit switch UP
Connection limit switch DOWN
30
31
32
33
The two pushbuttons UP and DOWN have to
be N.O. contact. If the STOP function is
connected in the safety circle, it has to be
N.C. contact.
!
Check settings of Jumper on
mainboard (see page 9)
and of DIP-Switches
on Comfort module
(see backpage )!
connection pull switch
Connecting a pull switch
On the screw terminals 56 & 57 a pull switch (NO contact) can be connected.
56
57
automatic closing function (ON /OFF)
It is possible to switch or switch off the automatic closing time by connecting an external
timer to the screw terminals 54 & 55.
54
55
54
55
54
55
automatic closing function ON automatic closing function OFF
In the event of the automatic closing function being switched on permanently the screw
terminals 54 & 55 have to be bridged.
The function of the pull switch is
UP/STOP/DOWN/STOP.
d
e
L
u
x
e
Connecting a photo-cell
To connect a photo-beam to cover the ‘drive through’ area the photo-beam is connected to
the terminals 51, 52 & 53. If the infrared beam of the photo-beam is broken during the
DOWN direction the door will stop and reverse to a fully open position. It is possible to con-
figure the Comfort module so that when the photo-beam is activated by traffic the automatic
closing time is reduced to 5 seconds.
Using a photo-cell with receiver and transmitter, the power supply is connected to the
terminals 52 & 53.
51
52
53
NC
CC
GND
+
Spannungs-
versorgung
Steuerlogik
button
UP
button
STOP
button
DOWN
logic board
power
supply
3,3 - 8,2 kΩ
… 6 …


Need help? Post your question in this forum.

Forumrules
1

Forum

geba-tronic-dc-3-eco---standard---de-luxe

Reset search

  • replacment had transmitters for gebatronic DC3 mini max 3 s Submitted on 31-1-2022 at 13:45

    Reply Report abuse

  • can i get replacemnt handheld transmitters for Gebatronic DC3 Mini Max 3S Submitted on 31-1-2022 at 13:44

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Geba Tronic DC 3 ECO - Standard - de Luxe at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Geba Tronic DC 3 ECO - Standard - de Luxe in the language / languages: English as an attachment in your email.

The manual is 0,75 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Geba Tronic DC 3 ECO - Standard - de Luxe

Geba Tronic DC 3 ECO - Standard - de Luxe User Manual - German - 18 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info