580308
29
Zoom out
Zoom in
Previous page
1/257
Next page
NX-10 Installers manual
29
not communicate with the panel in this time window, the learning mode is exited. The
learning mode can be restarted by switching panel power off and on again.
2. Insert the batteries in the wireless keypad. It starts the keypad initialization process.
Note: If the keypad is not brand new (i.e. it was already used with another system), it must be re-
programmed (flashed) first to erase any previous keypad settings, otherwise it will not initialize the learning
mode (see Chapter B11 Updating firmware on page 242).
3. Select a language from the list with the ½¾ keys and press OK.
4. Select default settings from the Load Country Defaults list with the ½¾ keys and press
OK.
5. At the Partition Number prompt, type the partition number and press OK.
6. At the Keypad Number prompt, type the keypad number and press OK.
7. At the SysID-KID1-KID2 prompt, 3 values need to be entered:
SysID: this value represents the System ID or a 3 digit code which should be unique
for this panel.
KID1: this value represents Keypad ID 1 and contains the first 3 digits of the code
which should be unique for this wireless keypad.
KID2: this value represents Keypad ID 2 and contains the last 3 digits of the code
which should be unique for this wireless keypad. Each of these three values must
range from 001 to 255. If any typed value is incorrect, the keypad displays the blank
SysID-KID1-KID2 prompt again. The combination of unique panel and wireless
keypad identifiers is required in order a wireless keypad is to communicate with the
appropriate panel only. In case multiple wireless keypads are used on the same panel,
each wireless keypad should have different KID1 and KID2 values.
8. At the EncKey prompt, enter a 24-digit encryption key and press OK. This encryption key
is to secure the wireless communication link between the panel and wireless keypad(s)
and is unique for each panel. Any 24-digit value can be entered. The same encryption key
must be entered in case other wireless keypads are enrolled.
9. The keypad communicates with the panel and sends data entered in steps 3 to 8. The
Learn-in Mode message displays briefly.
10. The keypad is learned-in and displays the System Ready message.
Important: You should not program zero-only strings (for example, "000") as values for SysID, KID1, KID2 nor
Encryption Key, as it will make the keypad non-operational.
Note: If the learned-in keypad's configuration stored in the RF receiver, differs from the actual keypad's configuration,
the RF receiver will start the configuration copying process. It takes a couple of seconds, and during this
process the keypad displays the "Copying" message. During this operation, due to an intensive radio
communication, you should not perform any additional actions on other wireless keypads.
Installing the wireless sirens
In order to guarantee communication between the panel and the siren, each siren must be learned-in.
This procedure requires starting the learn-in mode in the control panel with the menu, and then
tripping the tamper switch of the siren. For all steps required to program a new siren, see Learning-in
wireless sire
ns on page 166.
29


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for GE Security NetworX NX-10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of GE Security NetworX NX-10 in the language / languages: English as an attachment in your email.

The manual is 2,81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of GE Security NetworX NX-10

GE Security NetworX NX-10 Quick start guide - English - 6 pages

GE Security NetworX NX-10 User Manual - German - 40 pages

GE Security NetworX NX-10 Quick start guide - Dutch - 6 pages

GE Security NetworX NX-10 User Manual - Dutch - 38 pages

GE Security NetworX NX-10 Installation Guide - Dutch - 264 pages

GE Security NetworX NX-10 Quick start guide - French - 6 pages

GE Security NetworX NX-10 Installation Guide - French - 274 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info