580308
28
Zoom out
Zoom in
Previous page
1/257
Next page
4. At the panel side, run the NetworX bus wires through the ferrite (see Figure 9,
position
1), making one loop, and connect the wires to the standard NetworX bus
contacts (see Figure 1, position
4). Additionally, connect the shielding to COM (see
Figure 9, position
2).
Figure 9. Panel connector block and the ferrite.
5. Carefully close the keypad and tighten the 2 screws at the bottom side.
Note: Any opening of the keypad enclosure will cause tamper alarm in the system.
6. Power up the panel. Select a language from the list with the ½¾ keys and press OK.
7. Select default settings from the Load Country Defaults list with the ½¾ keys and press
OK.
8. At the Partition Number prompt, type the partition number and press OK.
9. At the Keypad Number prompt, type the keypad number and press OK.
There is a slight difference in keypad reaction speed between the wired and wireless keypad, because
the wireless keypad needs more time to communicate with the control panel. Please allow appropriate
time to send data between the panel and the wireless keypad, especially during programming, when
large amount of information is exchanged.
Wireless keypad learning-in procedure
Prior to installing a new wireless keypad into the system, the keypad should first be “learned-in” by
the panel in order to guarantee mutual recognition. With the first keypad successfully installed, the
installer can use this keypad to help learning-in additional ones. The installer can also delete any or
all of the keypads from the system.
For adding the first wireless keypad to the panel, the keypad learn-in procedure should be executed as
shown below. For instructions about installing additional wireless keypads, see
Learning-in
additional wireless keypads section.
1. Power up the panel. It starts the learning mode automatically. The panel stays in this
mode for 2 minutes allowing you to program the first wireless keypad. If the keypad does
1
2
28


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for GE Security NetworX NX-10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of GE Security NetworX NX-10 in the language / languages: English as an attachment in your email.

The manual is 2,81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of GE Security NetworX NX-10

GE Security NetworX NX-10 Quick start guide - English - 6 pages

GE Security NetworX NX-10 User Manual - German - 40 pages

GE Security NetworX NX-10 Quick start guide - Dutch - 6 pages

GE Security NetworX NX-10 User Manual - Dutch - 38 pages

GE Security NetworX NX-10 Installation Guide - Dutch - 264 pages

GE Security NetworX NX-10 Quick start guide - French - 6 pages

GE Security NetworX NX-10 Installation Guide - French - 274 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info