813416

Gazco Vision Large MK2 Series Balanced Flue Instructions Manual

30
Zoom out
Zoom in
Previous page
1/36
Next page
30
Servicing Instructions - Replacing Parts
8. Pilot Unit Assembly
8.1 Remove the screw retaining the pilot cover.
17
8.2 Cut the cable tie retaining the vidaex sleeve and disconnect
the ignition lead from the electrode.
4.0mm
18
13mm
8.3 Undo the pilot pipe and thermocouple from the rear of valve.
8.4 Remove the two xing screws and retain the vidaex sleeve
which is needed for the replacement.
8.5 Replace in reverse order.
8.6 Ensure the thermocouple and ignition lead are threaded
through the vidaex and secured with a cable tie. There is a
cut out in the pilot shroud to hold the vidaex.
8.7 Check for gas leaks.
9. Ignition Lead
9.1 Cut the cable tie securing the vidaex (if present) and
disconnect the ignition lead from the electrode.
9.2 Pull the lead through the vidaex.
9.3 Cut the remaining cable ties and disconnect the lead from
the control box, see Diagram 19.
19
9.4 Replace in reverse order.
9.5 Ensure the lead is passed through the vidaex, secured
with a cable tie and the red insulated end is attached to the
electrode.
NOTE: DO NOT ROUTE THE IGNITION LEAD
IN THE VICINITY OF THE ANTENNA ON
THE CONTROL BOX. THIS DAMAGES THE
COMPONENTS.
10. Gas Valve
To change the gas valve:
10.1 Disconnect the gas inlet pipe, Diagram 20, Arrow A.
10.2 Disconnect the gas outlet pipe, Diagram 20, Arrow B.
10.3 Disconnect the pilot pipe, Diagram 20, Arrow C.
10.4 Disconnect the thermocouple, thermo current wires and the
interrupter block, Diagram 20, Arrow D.
10.5 Remove the two screws and rotate the valve to access the
front.
10.6 The cable can now be removed from the valve, Diagram 20
Arrow E.
C
D
A
B
E
20
Replace in reverse order ensuring and check for leaks.
11. Magnetic Safety Valve
To replace the magnetic safety valve:
11.1 Undo the thermocouple from the interrupter block and
remove the two interrupter leads.
11.2 Unscrew the interrupter block from the back of the valve.
11.3 Undo the silver magnetic valve retaining nut on the back
of the valve.
11.4 Gently tap out the mag valve.
11.5 Replace with a new unit.
11.6 Reassemble in reverse order ensuring that the interrupter
leads are connected correctly with the red tag lead nearest
to the gas valve body.
11.7 Check for leaks.
… 30 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gazco Vision Large MK2 Series Balanced Flue Instructions at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gazco Vision Large MK2 Series Balanced Flue Instructions in the language / languages: English as an attachment in your email.

The manual is 4.65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info