813416

Gazco Vision Large MK2 Series Balanced Flue Instructions Manual

27
Zoom out
Zoom in
Previous page
1/36
Next page
27
Servicing Instructions - Replacing Parts
To completely remove the glass front:
3.3 Remove the securing spring clip from the bottom-right of the
window frame, see Diagram 3.
3
3.4 With the window frame in an upright position slide the frame
to the left so that it comes off the left hinge pin.
3.5 Still keeping the frame upright drop the left side down and
forward slightly, see Diagram 4.
4
3.6 Slide the frame to the right so it comes off the right hinge
pin. The window frame should now be free.
3.7 Refit in reverse order.
3.8 When closing the door ensure the door catches are fully
engaged.
UNDER NO CIRCUMSTANCES SHOULD THE
APPLIANCE BE USED WITHOUT THE CATCHES
HOLDING THE DOOR IN PLACE.
4. Glass Window
4.1 Remove the 2 clips and brackets from either side of the
frame, see Diagram 5.
5
4.2 Lift the glass clear from the lock bracket at the top of the
frame and slide out.
1. General
1.1 All main components can be replaced without removing the
appliance from its installation.
IT IS ESSENTIAL THAT THE GAS SUPPLY TO THE
APPLIANCE IS TURNED OFF AT THE ISOLATION
DEVICE BEFORE PROCEEDING FURTHER.
1.2 DISCONNECT BATTERIES BEFORE SERVICING THE
APPLIANCE.
1.3 Removal of Flue
If, for any reason, the flue has to be removed from the
appliance, the seal must be replaced in the inner spigot.
1.4 Access to the controls is restricted and the whole of the
control assembly is to be removed as one unit, see
Servicing Section 8.
2. Decorative Front
IMPORTANT: THE OUTER PANELLING OF THE
VISION IS MADE FROM GLASS. USE CAUTION
WHEN INSTALLING, REMOVING AND STORING AS
THE COMPONENTS ARE FRAGILE AND COULD
BREAK UNLESS HANDLED CAREFULLY.
1
2.1 Lift the front off the main body and pull forward.
3. Window Frame Assembly
3.1 To open the glass door use the hexagon key provided.
3.2 Release the window locks by moving them from shut to
open towards the outer edges, see Diagram 2.
2
… 27 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gazco Vision Large MK2 Series Balanced Flue Instructions at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gazco Vision Large MK2 Series Balanced Flue Instructions in the language / languages: English as an attachment in your email.

The manual is 4.65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info