813415
27
Zoom out
Zoom in
Previous page
1/36
Next page
27
ELECTRONICCONTROLVALVE
FAULT ANALYSIS
Problem Cause Error Message LCD Display Solution
Does not ignite
No batteries or at batteries in battery box 10 beeps BATTERY
ERROR Place new batteries in battery box
ROM error 2 cycles of 3 beeps ROM ERROR Change control unit
Support test error 2 cycles of 5 beeps SUPPORT
ERROR Connect earth cable from control box to valve
Bad reception of remote handset signal
Change batteries in the remote handset
Check the reception of signal from a shorter distance
Try pairing again
Try changing the channel in the conguration menu
No response to touch control buttons If LED is continuously
on, the cable is con-
nected the wrong way
round
Ensure the touch control cable is correctly connected
(see installation manual)
Cable loose or broken or connected
wrong way round Change touch control
Supply cable to valve disconnected or
broken 2 cycles of 5 beeps SUPPORT
ERROR Reconnect or replace valve cable
Ignition cable disconnected or broken Connect ignition cable
Sparks but no pilot
ignition
Gas valve supply off or no gas Check gas installation. Open gas valve
Valve cable disconnected or broken Connect valve cable correctly
Interrupter cable disconnected or broken Connect correctly or replace pilot cable
Pilot ignites but does
not stay on
Pilot is not warmed up Check pilot ame and verify that it heats the pilot
Interrupter cable badly connected Change polarity of pilot cable
Interrupter cable disconnected or broken Connect pilot cable
Ignites from remote
handset but not from
touch pad
Touch control cable disconnected or
broken Connect or replace touch control cable
Defective touch control buttons Change touch control
Ignites from touch pad
but not from remote Bad communication with handset
Check batteries in handset
Check reception of signal from a shorter distance
Try pairing again
Try changing the channel in the conguration menu
Switches off after 6
seconds Short circuit in touch control 5 beeps BUTTON ER-
ROR Change touch control wiring
Low batteries on
remote Low battery Change the batteries in the remote
Appliance switches off
2 cycles of 3 beeps CONFIG
ERROR Change control unit
2 cycles of 3 beeps EEPRON
ERROR
Try pairing again
Change control unit
Loss of communication between
appliance and remote for 18min 20 beeps The remote is too far from the appliance
Replace batteries in handset
High temperature on control unit 1 long beep TEMP ERROR If this occurs more than once call the technical service
Ambient temperature higher than con-
gured
Over
Temperature
Check the correct conguration of safety
temperature
Fault Finding Charts
Servicing Instructions
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gazco Riva Vision Large MK1 Series Conventional Flue at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gazco Riva Vision Large MK1 Series Conventional Flue in the language / languages: English as an attachment in your email.

The manual is 3.57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info