813414

Gazco Riva Vision Large MK1 Series Balanced Flue Instructions Manual

36
Zoom out
Zoom in
Previous page
1/40
Next page
36
Servicing Instructions - Replacing Parts
Touch Pad
Supply Cable
Battery Power
Supply
Touch Pad
Control
Ignition
Lead
Stepper Motor Cable
Pilot Pipe
Thermocouple
Earth Lead
Interrupter Leads
23
13.5 Prior to re-connection of the control box to the appliance, if
there is no communication between the remote handset and
the appliance, or if the handset is replaced, it will be
necessary to pair the handset with the appliance. Please
refer to Commissioning Section 2.
13.6 Ensure batteries are fitted and working in the handset.
13.7 Re-fit the touch pad control cable and the battery power
supply cable to the control box.
14. Main Injector
To change the main injector:
14.1 Undo the injector fee pipe.
14.2 Undo the lock nut from the injector.
14.3 Replace with the correct size injector.
15. Primary Aeration Plate
NOT ALL MODELS HAVE AERATION PLATES. REFER TO
TECHNICAL SPECIFICATIONS, PAGES 13 & 14.
15.1 Remove the burner module as described in Servicing,
Section 7.
15.2 Remove the fixing screw and slide the plate off the venturi.
15.3 Replace with the correct size plate and secure with the
screw. Ensure the lower edge of the plate is located over
the venturi flange, see Diagram 24.
24
16. Changing Between Gas Types
In order to change between gas types it will be necessary to
change both the burner assembly and the complete control
assembly.
Contact your Gazco retailer for further information.
A kit of parts is available for this. Always quote the Model
number and Serial number when ordering any spare parts.
17. Pressure and leak testing the
appliance
17.1 To gain access to the pressure test point, see Diagram 25
follow Section 8, Main Control Assembly.
25
17.2 To leak test any gas joints on the appliance the control
assembly must be undone and tilted backwards, see
Section 8.2, Diagram 13.
17.3 Because there is now no burner fitted to perform a leak test,
place a manometer tube over the injector tip.
17.4 Light the appliance and spray any joints with leak
detector fluid.
17.5 Tighten joints or replace as required.
17.6 To check the inlet working pressure, replace the control
assembly and connect a manometer to the pressure test
point, see Diagram 26.
17.7 Replace the burner and relight the appliance.
17.8 Operate the appliance at highest flame setting and check
that the inlet pressure is in accordance with specifications
detailed on pages 12 & 13.
… 36 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gazco Riva Vision Large MK1 Series Balanced Flue Instructions at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gazco Riva Vision Large MK1 Series Balanced Flue Instructions in the language / languages: English as an attachment in your email.

The manual is 4.28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info