813421

Gazco riva Vision Large 50000 series Conventional Flue Instructions Manual

27
Zoom out
Zoom in
Previous page
1/32
Next page
27
Servicing Instructions - Replacing Parts
12. Magnetic Safety Valve
To replace the magnetic safety valve:
12.1 Undo the thermocouple from the interrupter block and
remove the two interrupter leads.
12.2 Unscrew the interrupter block from the back of the valve.
12.3 Undo the silver magnetic valve retaining nut on the back
of the valve.
12.4 Gently tap out the mag valve.
12.5 Replace with a new unit.
12.6 Reassemble in reverse order ensuring that the interrupter
leads are connected correctly with the red tag lead nearest
to the gas valve body.
12.7 Check for leaks.
13. Control Box
13.1 To replace the control box first remove the main control
assembly, See Section 7.
13.2 Remove the two thermocurrent cables by removing the two
screws, Diagram 19.
13.3 Remove the ignition lead, Diagram 19.
13.4 Remove the eight wire loom from the control box.
13.5 Remove the battery extension cable, Diagram 19.
The control box can now be replaced.
When replacing the sealing plate on the rear of the control
cover use a suitable silicone sealant.
Battery
extension
cable
Eight wire
cable
Thermo current
cables
Ignition lead
19
13.6 After replacing the control box you may need to reprogram
the handset.
— Press and hold the reset button on the control box until
you hear two signals. After the second longer signal:
— Release the reset button and within 20 seconds:
— Press the DOWN button on the handset until you hear
two additional short signals confirming the new code is set.
If there is a single long signal the code learning sequence
has failed or the wiring is incorrect.
14. Main Injector
To change the main injector:
14.1 Undo the injector feed pipe.
14.2 Undo the lock nut from the injector and remove the
silencer.
14.3 Replace with the correct size injector.
14.4 Check for leaks.
15. Primary Aeration Plate
NOT ALL MODELS HAVE AERATION PLATES. REFER
TO TECHNICAL SPECIFICATIONS ON PAGE 13.
15.1 Remove the burner module as described in Replacing Parts,
Section 7.
15.2 Remove the fixing screw and slide the plate off the venturi.
15.3 Replace with the correct size plate and secure with the
screw. Ensure the lower edge of the plate is located over
the venturi flange, see Diagram 20.
20
… 27 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gazco riva Vision Large 50000 series Conventional Flue Instructions at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gazco riva Vision Large 50000 series Conventional Flue Instructions in the language / languages: English as an attachment in your email.

The manual is 2.97 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info