813421

Gazco riva Vision Large 50000 series Conventional Flue Instructions Manual

14
Zoom out
Zoom in
Previous page
1/32
Next page
14
Installation Instructions
1. Safety Precautions
1.1 For your own and other’s safety, you must install this
appliance according to local and national codes of practice.
Failure to install the appliance correctly could lead to
prosecution. Read these instructions before installing
and using this appliance.
1.2 These instructions must be left intact with the user.
1.3 Do not attempt to burn rubbish on this appliance.
1.4 Keep all plastic bags away from young children.
1.5 Do not place any object on or near to the appliance and
allow adequate clearance above the appliance.
IF THE APPLIANCE IS EXTINGUISHED OR GOES OUT
IN USE, WAIT 3 MINUTES BEFORE ATTEMPTING TO
RELIGHT THE APPLIANCE.
IMPORTANT: REFER TO DATA BADGE AND
TECHNICAL SPECIFICATION AT THE FRONT OF THE
MANUAL TO ENSURE THE APPLIANCE IS
CORRECTLY ADJUSTED FOR THE GAS TYPE AND
CATEGORY APPLICABLE IN THE COUNTRY OF USE.
FOR DETAILS OF CHANGING BETWEEN GAS TYPES
REFER TO SERVICING, SECTION 17, REPLACING
PARTS.
Unpacking
1.6 Remove the appliance from its packaging, and check that it
is complete and undamaged.
1.7 The glass lid is stored on top of the appliance. Remove and
store in a safe place.
Put the loose ceramic parts to one side so that they are not
damaged during installation.
2. Installation of the Appliance
IMPORTANT: THE OUTER PANELLING OF THE RIVA
VISION IS MADE FROM GLASS. USE CAUTION
WHEN INSTALLING, REMOVING AND STORING AS
THE COMPONENTS ARE FRAGILE AND COULD
BREAK UNLESS HANDLED CAREFULLY.
Please note: As an optional extra Gazco can provide
a mains adapter to supply constant power to the
appliance control box instead of the battery pack.
If installing an appliance with the adapter make
provision for a mains power socket within 1.5m of
the control box and follow the instructions provided.
2.1 Remove the front from the appliance by lifting clear of the
slotted hooks, see Diagram 1.
1
Use the hex key provided to release the window locks
moving each from shut to open towards the outer edge of
the glass door, see Diagram 2.
2
2.2 Remove the box from the appliance and store safely as it
contains the remote control and fuel effects.
2.3 Remove all the enamel or vermiculite liners where
necessary.
2.4 To access the controls and pressure test point:
Remove the glass front, liners, burner and splitter plate,
refer to Servicing, Replacing Parts, Section 3 - 7.
2.5 Check the pull of the flue system by applying a lighted
smoke pellet to the flue system opening If there is a definite
flow into the chimney, proceed with the installation. If not,
warm the chimney for a few minutes.
IF THERE IS STILL NO DEFINITE FLOW, THE FLUE MAY
REQUIRE ATTENTION - SEEK EXPERT ADVICE
3
A drilling template is supplied in order to locate the
fixing plates.
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gazco riva Vision Large 50000 series Conventional Flue Instructions at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gazco riva Vision Large 50000 series Conventional Flue Instructions in the language / languages: English as an attachment in your email.

The manual is 2.97 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info