813402
19
Zoom out
Zoom in
Previous page
1/34
Next page
19
INSTALLATION INSTRUCTIONS
INSTALLATION
5. FITTING THE DOOR
5.1 Ensure that the fibreglass seal on the back of the glass frame
is intact then hook the location tabs over the hooks on the
top of the firebox. Replace the nine screws working from
the top down. Tighten the screws evenly. DO NOT OVER
TIGHTEN (see Diagram 21).
NEVER OPERATE THE APPLIANCE WHEN THE GLASS
PANEL IS REMOVED OR BROKEN.
5.2 Close the front door of the appliance by pushing centrally
on the RH side, the door catch should locate in the closing
mechanism and finish in the closed position.
5.3 It may be necessary to re-adjust the door closing
mechanism due to vibration whilst in transit. Vertical
adjustment should be made by loosening the two nuts
directly above and below the locking mechanism on the RH
internal side of the outer body (see Diagram 21).
AR1295
21
5.4 Horizontal adjustment should be made by loosening the
two bolts, which hold the locking catch to the rear of the
door (see Diagram 22).
AR1296
22
6A. OPERATING THE APPLIANCE
IMPORTANT - THE CONTROL SYSTEM HAS BEEN
PROGRAMMED TO OPERATE ON CHANNEL 'A'. IN
SOME INSTANCES MULTIPLE HOUSEHOLD APPLIANCES
MAY HAVE ALSO BEEN SET TO OPERATE ON THE SAME
CHANNEL. ALTHOUGH THIS HAS NO EFFECT ON THE
SAFETY OF THE SYSTEM YOU MAY ENCOUNTER AN
EXCESSIVE DELAY BETWEEN COMMANDS. IF THIS
OCCURS PLEASE FOLLOW THE INSTRUCTIONS IN
INSTALLATION INSTRUCTIONS, COMMISSIONING,
SECTION 3 TO CHANGE THE CHANNEL.
The remote control handset has been factory set to only
communicate with the appliance it is supplied with. The
appliance will not respond to any other remote control,
even one from an identical appliance.
Note: In the event of a replacement handset being
acquired, pairing of the handset with the appliance will
need to be carried out. Please refer to Commissioning,
Section 2, Pairing Handset on page 21.
The appliance can be operated in two ways:
Using the remote control handset.
Using the touch pad control on the appliance.
The appliance has four flame settings which can be
controlled manually or automatically via temperature
sensing:
1. High (Pilot lit and main burner lit at the highest
flame setting).
2. Med (Pilot lit and main burner lit at the medium
flame setting).
3. Low (Pilot lit and main burner lit at the minimum flame
setting).
4. Standby (Pilot only).
23
AR2516a
On/Off
Button
Up
Button
Down
Button
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gazco Riva Nemos Coprecci at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gazco Riva Nemos Coprecci in the language / languages: English as an attachment in your email.

The manual is 3.17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info