813405
16
Zoom out
Zoom in
Previous page
1/40
Next page
16
NOTE ON INSTRUCTIONS
The instruction in this document applies to the following
three Riva models:
• F67RivaPedestal
• F67RivaBench
• F67Riva
The instructions vary only where a particular feature of a
specific model requires explanation. Otherwise the
instructions should be understood as applicable to all
three models.
IMPORTANT: ENSURE THAT THE APPLIANCE IS
CORRECTLY ADJUSTED FOR THE GAS TYPE AND
CATEGORY APPLICABLE IN THE COUNTRY OF USE.
REFER TO DATA BADGE AND TECHNICAL
SPECIFICATIONS AT THE FRONT OF THE BOOKLET.
LPG MODELS: THE APPLIANCE IS FACTORY SET TO RUN
ON BUTANE (G30). IF IT IS INTENDED TO BE USED ON
PROPANE (G31) THE AERATION PLATE SUPPLIED MUST
BE FITTED.
TO CHANGE AERATION PLATE REFER TO REPLACING
PARTS, SECTION 8 (BALANCED FLUE) OR 9
(CONVENTIONAL FLUE).
FOR DETAILS OF CHANGING BETWEEN GAS TYPES
REFER TO REPLACING PARTS, SECTION 10 (BALANCED
FLUE) OR 11 (CONVENTIONAL FLUE).
1. SAFETY PRECAUTIONS
1.1 This appliance must be installed in accordance with the
rules in force, and used only in a sufficiently ventilated
space. Please read these instructions before installation and
use of this appliance.
1.2 These instructions must be left intact with the user.
1.3 Do not attempt to burn rubbish on this appliance.
1.4 In your own interest, and those of safety, this appliance
must be installed by competent persons in accordance with
local and national codes of practice. Failure to install the
appliance correctly could lead to prosecution.
1.5 Keep all plastic bags away from young children.
1.6 Do not place any object on or near to the appliance. Allow
adequate clearance above the appliance.
IF THE APPLIANCE IS EXTINGUISHED OR GOES OUT IN
USE, WAIT 3 MINUTES BEFORE ATTEMPTING TO
RELIGHT THE APPLIANCE.
2. INSTALLATION OF THE APPLIANCE
NOTE: THERE IS AN OPTIONAL CONVECTION FAN KIT
AVAILABLE [8566 Balanced Flue or 8571 Conventional
Flue]. THIS CAN BE FITTED EITHER DURING OR AFTER
INSTALLATION, BUT PROVISION FOR A POWER SUPPLY
MUST BE MADE PRIOR TO INSTALLATION OF THE
APPLIANCE.
2.1 Remove the appliance from the carton and discard all
unnecessary packaging. Ensure no components are thrown
away when unpacking.
2.2 Unpack the Spectrum frame supplied with the appliance
and place to one side.
2.3 F67 Riva Bench only
2.3.1 To secure the bench to the floor:
• Positionthebenchwhererequired
• Mark its position on the floor through the keyholes in the
small opening on both legs (see Diagram 1).
1
AR1895
• Removethebench
• Drillandfitfixingscrewsinthefloor
• Partiallytightenprovidingenoughmargintothen:
• Manoeuvrethebenchandslidethekeyholesintothe
screws
• Tightenthescrewsfully
2.3.2 To secure the appliance to the bench you must consider
where you place the appliance on the bench before using
the template (see Diagram 2).
2
AR1894
INSTALLATION INSTRUCTIONS
INSTALLATION
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gazco Riva F67 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gazco Riva F67 in the language / languages: English as an attachment in your email.

The manual is 4.73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info