813405

Gazco Riva F67 Manual

15
Zoom out
Zoom in
Previous page
1/40
Next page
3.5 EXTRA FLUE LENGTHS
All flue components are 150mm diameter (6")
NOMINAL
LENGTH ACTUAL
LENGTH STAINLESS
FINISH ANTHRACITE
FINISH
200mm 140mm 8527 8527AN
500mm 440mm 8528 8528AN
1000mm 940mm 8529 8529AN
40° Bend N/A 8507 8507AN
90° Bend N/A 8508 8508AN
NOTE: The following areas need careful consideration:
a) Terminal positions
b) Flue supports
c) Weatherproofing
d) Fire precautions
For all the above options, local and national codes of practice
must be adhered to.
CONVENTIONAL & BALANCED FLUE
4. GAS SUPPLY
4.1 Before installation, ensure that the local distribution
conditions (identification of the type of gas and pressure)
and the adjustment of the appliance are compatible.
4.2 Ensure that the gas supply is capable of delivering the
required amount of gas and is in accordance with the rules
in force.
4.3 Soft copper tubing can be used to install the appliance. Soft
soldered joints can be used externally of the appliance but
must be restricted to the area shown in Diagram 2.
4.4 This appliance is supplied complete with a factory fitted
isolation device incorporated into the inlet connection, no
further isolation device is required.
4.5 All supply gas pipes must be purged of any debris that may
have entered, prior to connection to the appliance.
4.6 The gas supply enters through the silicone panel located on
the RH side of the outer box; this will need to be slit with a
sharp knife prior to passing the supply pipe through.
5. VENTILATION
5.1 This appliance requires no additional ventilation.
15
INSTALLATION INSTRUCTIONS
SITE REQUIREMENTS - CONVENTIONAL & BALANCED FLUE
6. APPLIANCE LOCATION
6.1 With the exception of the F67 Riva (see below), it is not
necessary to site these products on a non-combustible floor.
However, for practical reasons, the floor should be flat and
solid to allow the appliance to be levelled and secured in
place.
6.2 This appliance may be situated anywhere in the room, but
due consideration should be taken to ensure that it is sited
within the constraints of the allowable flue configuration.
6.3 As well as allowing for the flue position, you must also
consider the position of bench and the F67 upon the
bench.
6.4 If the appliance is to be sited against a combustible wall, a
clearance of 50mm should be allowed between the wall
and the rear of the appliance.
6.5 F67 Riva
The F67 Riva requires a non-combustible hearth.
A non-combustible hearth must be at least 12mm thick and
project 50mm from the base of the stove in all directions.
The minimum dimensions are shown in Diagram 2.
2
AR0604
MINIMUM CLEARANCE
A = 980 mm
B = 520 mm
C = Minimum 12 mm
6.6 F67 Riva Pedestal & F67 Riva Bench
6.6.1 The Riva Pedestal or the Riva Bench does not need a
non-combustible floor but the appliance must not be
fitted on a carpet. Use a solid floor.
6.6.2 These two appliances can be situated anywhere in the
room but when siting you must consider the constraints
of the flue.
6.6.3 If the appliance is to be sited against a wall, a clearance
of 50mm must be allowed between the wall and the
appliance.
… 15 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gazco Riva F67 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gazco Riva F67 in the language / languages: English as an attachment in your email.

The manual is 4.73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info