813406

Gazco Riva 2 F670 Balanced Flue Manual

6
Zoom out
Zoom in
Previous page
1/44
Next page
6
2.8 P1 - Program 1 for a Timed Setting
Press the SET button until the TIMER mode is displayed.
Hold the SET button. The displays flashes the current time
for P1. While the time displayed is flashing you can alter
the hours and minutes set.
To set the time your appliance first lights, change P1
— Press the UP button to alter the hour.
— Press the DOWN button to alter the minutes in 10
minute increments.
Press SET again to move to the end setting for P1 This is
the time your Studio first shuts down:
— Press the UP button to alter the hour.
— Press the DOWN button to alter the minutes.
2.9 P2 - Program 2 for a Timed Setting
Use the same steps outlined in 2.8 to change the setting
for P2.
If you have already set P1 and want to alter the setting for
P2 only:
— Press the SET button until TIMER mode is displayed.
— Hold the SET button until the display flashes the
current time for P1 .
— Press the SET button once again to scroll past the
settings for P1 and P1.
With the time still flashing:
— Press the UP button to alter the hour.
— Press the DOWN button to alter the minutes.
Once all four times are set press the OFF button.
2.10 To view existing settings:
— Select Timer Mode.
— Press and briefly hold the SET button you see the start
time for P1.
— Repeat the above step for the start and end of each
program.
Low Battery
“BATT” is displayed on the remote when its batteries need
replacement.
Setting the time
Simultaneously press the up and down buttons.
Press the up button to set the hour and the down button to
set the minutes.
Press OFF to return to the manual mode or simply wait.
Setting the °C/24 Hour or °F/12 Hour clock
Press OFF and the down arrow until the display changes
from °C/24 hour clock to °F/12 hour clock and vice versa.
If the remote is removed, lost or damaged, signals
transmitted to the receiver cease. Your appliance will
go to standby (pilot) mode after 6 hours.
Troubleshooting
IMPORTANT: In the unlikely event that the handset
fails to communicate correctly with the appliance
it may be necessary to turn off the gas supply at
the isolation valve until any problems can be
resolved.
The gas meter and isolation valve can be located
outside in a meter box, under the stairs, beneath
the kitchen sink or in the garage. Whilst this list is
not exhaustive, it is important to be able to
identify the location of the valve in case of any
gas emergency.
To turn off the gas supply, simply turn the handle
so the lever is at 90 degrees to the upright gas
pipe.
If you smell gas, open doors and windows and
never operate any electrical switches.
Immediately call the Gas Emergency Services on
0800 111 999.
3. Removing the Decorative Front
3.1 Remove the decorative front by lifting to disengage the
fixing hooks from the locating slots, see Diagram 2.
2
3.2 Place carefully to one side.
3.3 Replace in reverse order.
User Instructions
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gazco Riva 2 F670 Balanced Flue at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gazco Riva 2 F670 Balanced Flue in the language / languages: English as an attachment in your email.

The manual is 4.76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info