813396

Gazco F40 Avanti Conventional Coal Manual

12
Zoom out
Zoom in
Previous page
1/23
Next page
definite flow into the chimney, proceed with the
installation, if not warm the chimney for a few minutes.
IF THERE IS STILL NO DEFINITE FLOW, THE FLUE MAY
REQUIRE ATTENTION - SEEK EXPERT ADVICE.
3.14 The flue system may now be connected to the stove, ensure
that all joints are sealed with a suitable fire resistant sealant.
It is also recommended that a physical retention method be
used at the flue spigot joint, self-tapping screws being
favoured.
3.15 Connect a suitable pressure gauge to the test point located
on the inlet fitting, and turn the gas supply on. Light the
stove and check all gas joints for gas soundness. Turn the
stove to maximum and check that the supply pressure is as
stated on the data badge. Turn the gas off and replace the
test point screw, turn the gas on and check the test point for
gas soundness.
4. HANDLING & DISPOSAL OF FIRE
CERAMICS
The fuel effect and side panels in this appliance are made
from Refractory Ceramic Fibre (RCF), a material which is
commonly used for this application.
Protective clothing is not required when handling these
articles, but we recommend you follow normal hygiene rules
of not smoking, eating or drinking in the work area and
always wash your hands before eating or drinking.
To ensure that the release of RCF fibres are kept to a
minimum, during installation and servicing a HEPA filtered
vacuum is recommended to remove any dust accumulated
in and around the appliance before and after working on it.
When servicing the appliance it is recommended that the
replaced items are not broken up, but are sealed within
heavy duty polythene bags and labelled as RCF waste.
RCF waste is classed as stable, non-reactive hazardous waste
and may be disposed of at a licensed landfill site.
Excessive exposure to these materials may cause temporary
irritation to eyes, skin and respiratory tract; wash hands
thoroughly after handling the material.
5. FUEL BED ARRANGEMENT
5.1 Place the flame baffle onto the burner and push against the
rear tray lip. See diagram 9.
9
AR0359
5.2 Locate the rear panel against the spacer brackets and slide
down so that it locates on the ledge of the flame baffle. See
diagram 10.
10
AR0360
5.3 Locate the front coal between the heat shield and the flame
baffle so its ends sit flat on the burner skin. See diagram 11.
11
AR0361
5.4 Place five of the loose round coals on the front coal so they
lean against the flame baffle, in between the fingers. Place
the two rectangular coals against the reflector panels, one
either side, behind the front row of loose coals. See diagram
12.
12
AR0362
5.5 Place four of the loose round coals behind the first row so
that they sit on the fingers, the two outer ones should touch
the rectangular coals. See diagram 13.
13
AR0363
12
INSTALLATION INSTRUCTIONS
INSTALLATION
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gazco F40 Avanti Conventional Coal at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gazco F40 Avanti Conventional Coal in the language / languages: English as an attachment in your email.

The manual is 3.44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info