813468
4
Zoom out
Zoom in
Previous page
1/28
Next page
4
2.3 Dispose of old batteries at an appropriate recycling facility.
When using the handset:
2.4 Ensure the handset is pointed at the infrared sensor
located behind the flame effect screen at the back of the
inside of the appliance.
LOCATION OF POWER SWITCH
2.5 The mains power switch is located on the control panel on
the lower right-hand side of the stove, see Diagram 1.
2.6 Switch ON () before operating either the remote or
manual controls.
2.7 A beep is heard to indicate the fire is ready for use.
Remote & Manual Operation
2.8 The following functions can be controlled using the manual
controls or remote handset:
— Heat settings 1 and 2
— Brightness of the fuel and flame effect
— Colour of the flames
2.9 The Standby function and the thermostat can only be
operated via the manual controls.
2.10 The effects can be turned off using the remote, returning the
appliance to Standby.
Flame effect button Standby
On/Off Switch
Thermostat
Heat setting button
1
On/Off button
Flame effect
Heat setting 1kW
Heat setting 2kW
2
Standby On/Off
2.11 The appliance is in Standby mode when the power is
switched on via the manual control panel. You must have
this power supply ON () before using the manual or
remote controls (see 2.5).
Turning On the Appliance
Flame Effects:
2.12 The flame effect button on both the manual and remote
controls has 4 settings:
— Press once for maximum brightness of fuel and
flame effects.
— Press twice for medium brightness.
— Press three times for minimum brightness.
— Press four times for maximum brightness of fuel and
additional blue flame effects.
1234
Maximum Medium Minimum
Maximum
plus blue
ame effects
Turning On the Heat:
2.13 When turning on the heater you must always press the
1kW button. Do not start the fire using the 2kW setting.
2.14 It is NOT advisable to run the heater without the flame
effects switched on.
2.15 Press the 1kW button to turn the fan heater ON. One
red indicator light will be displayed behind the flame effect
screen at the back of the inside of the appliance. The
appliance will blow cold air for approximately 8 seconds
before the heater comes on. On this setting the heater will
operate at half its maximum temperature.
2.16 Press the 2kW button once to turn the fan heater to its
maximum temperature. Two red indicator lights will be
displayed behind the flame effect screen at the back of the
inside of the appliance. After approximately 8 seconds the
heater will operate at its maximum temperature.
2.17 Pressing the 2kW button again will turn the heater OFF
and cold air will be blown for approximately 8 seconds to
cool the appliance.
2.18 Press the 1kW button to return to the lower heat setting.
2.19 Press the On/Off button to turn off ALL settings and
return to Standby. Cold air will be blown for
approximately 8 seconds to cool the appliance.
2.20 The appliance should be turned off via the On/Off
switch when it is not in use.
User Instructions
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gazco Ashdon - Electric at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gazco Ashdon - Electric in the language / languages: English as an attachment in your email.

The manual is 4.66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Gazco Ashdon - Electric

Gazco Ashdon - Electric User Manual - Dutch - 20 pages

Gazco Ashdon - Electric User Manual - French - 20 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info