629028
6
Zoom out
Zoom in
Previous page
1/16
Next page
3
Charge the battery completely.
Saving Energy While Charging the Device
You can turn off the device screen and all other features while
charging.
1
Connect your device to an external power source.
2
Hold POWER for 4 to 5 seconds.
The screen turns off, and the device goes into a low power,
battery charging mode.
3
Charge the device completely.
Attaching the Device to the Mount
NOTICE
To prevent product loss or damage, do not use the adhesive
mounting base when the temperature is below -15°C (5°F).
The permanent mounting adhesive is extremely difficult to
remove after it is installed.
Before you can install the adhesive mounting base onto a
surface, the ambient temperature must be from 21° to 38°C
(from 70° to 100°F).
Your device includes an assortment of mounting bases and
arms, which can be used in many configurations. These
instructions provide an example of one possible configuration.
You can also purchase additional mounts for your device, such
as wearable mounts, vehicle mounts, or a tripod mount. Go to
www.garmin.com/VIRB for more information.
NOTE:
By default, the device should be mounted with the
screen facing up to record correctly oriented video. You can
adjust the settings to record with the screen facing down
(
Inverting the Camera Orientation,
page
8)
.
1
Thoroughly clean and dry the mounting surface using water
or alcohol.
The mounting surface must be free of dirt, debris, wax, or
coatings.
2
Remove the film from the adhesive mounting base
À
, and
press the base firmly onto the mounting surface.
You can use either the flat base or the curved base,
depending on the contour of the mounting surface.
3
Allow the base to bond to the mounting surface for at least 24
hours.
4
Insert the adapter
Á
into the base.
The lever
Â
must be in the open position.
5
Snap the lever to the closed position to lock the adapter into
the base.
The lever should be flush with the base.
6
Insert the camera mount
Ã
into the top of the adapter.
The device should be horizontal for the proper aspect ratio
when recording video.
7
Insert a thumbscrew
Ä
into the larger opening of the joint,
and tighten the thumbscrew to lock the angle of the joint.
NOTE: The metal fitting indicates the smaller opening of the
joint.
8
If necessary, insert the included hex wrench into the end of
the thumbscrew to adjust the tightness of the joint.
Keys
À
MENU Select to scroll through sensor status screens,
data screens, and menu items.
Hold to open the menu.
Á
POWER Select to scroll through sensor status screens,
data screens, and menu items.
Hold to turn the device on or off.
Â
OK Select to choose menu options or to take a photo.
Ã
Recording
switch
Move the switch to start or stop recording video.
Turning On the Device
Select POWER.
Turning Off the Device
NOTICE
To prevent loss of data, always turn off the device before
removing the battery.
NOTE: You cannot turn off the device while recording video.
1
If necessary, move the recording switch backward to stop
recording video.
2
Hold POWER.
The device saves your data and turns off.
If you need to remove the battery, wait until the screen and the
recording light turns off before removing the battery.
Turning the Device On and Off Using the Recording
Switch
You can use the recording switch to turn the device on and off in
recording mode. This feature allows you to start recording
quickly, while automatically turning off the device to conserve
battery power when you are not recording.
NOTE: The device does not turn off using the recording switch
unless you use the recording switch to turn on the device.
1
With the device turned off, move the recording switch
forward.
The device turns on and starts recording video.
2
When you are finished recording, move the recording switch
backward.
The device stops recording and turns off.
Home Screen Overview
The home screen provides at-a-glance details about the
remaining memory card space and current settings of your
device.
2 Introduction
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Garmin VIRB XE Actioncam at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Garmin VIRB XE Actioncam in the language / languages: English as an attachment in your email.

The manual is 1,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Garmin VIRB XE Actioncam

Garmin VIRB XE Actioncam User Manual - Dutch - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info