589619

Garmin Vector Manual

6
Zoom out
Zoom in
Previous page
1/14
Next page
3On the pedal spindle, stack the pedal pod and any required
washers Â.
TIP: You must carefully bend the cable à out of the way.
4Insert the spindle into the crank arm Ä.
5Hand tighten the spindle.
NOTE: The left pedal spindle has a left-handed (reverse)
thread.
TIP: Power and cadence calculations are not impacted by
the orientation of the pedal pod. Garmin® recommends
placement of the pedal pod on the leading edge of the crank.
When the crank is in the forward position, the pedal pod
should be pointing downward.
6Rotate the crank arm to check for clearance.
The pedal pod should not interfere with any part of the bike.
7Use the pedal wrench to tighten the spindle.
NOTE: Garmin recommends torque of 25 to 30 lbf-ft. (34 to
40 N-m).
8Firmly plug the cable into the spindle.
9Rotate the crank arm to check for clearance.
10Repeat steps 2–9 to install the right pedal.
NOTE: If the pedal pod cable rubs the chain, you can add
one or two washers between the pedal pod and the crank
arm to increase clearance.
Installing the Left Pedal and Pedal Pod
This procedure is for the Vector S system.
1Apply a thin layer of grease on the pedal spindle À and the
pedal pod Á where it contacts the pedal spindle.
2On the pedal spindle, stack the pedal pod and any required
washers Â.
NOTE: You must carefully bend the cable à out of the way.
NOTE: Do not use more than two washers.
3Insert the spindle into the crank arm Ä.
4Hand tighten the spindle.
NOTE: The left pedal spindle has a left-handed (reverse)
thread.
TIP: Power and cadence calculations are not impacted by
the orientation of the pedal pod. Garmin recommends
placement of the pedal pod on the leading edge of the crank.
When the crank is in the forward position, the pedal pod
should be pointing downward.
5Rotate the crank arm to check for clearance.
The pedal pod should not interfere with any part of the bike.
6Use the pedal wrench to tighten the spindle.
NOTE: Garmin recommends torque of 25 to 30 lbf-ft. (34 to
40 N-m).
7Firmly plug the cable into the spindle.
8Rotate the crank arm to check for clearance.
Installing the Right Pedal
This procedure is for the Vector S system.
1Apply a thin layer of grease on the pedal spindle.
2Insert the spindle into the crank arm.
NOTE: If you used one or two washers on the left pedal, use
the same amount on the right pedal.
3Hand tighten the spindle.
4Use the pedal wrench to tighten the spindle.
NOTE: Garmin recommends torque of 25 to 30 lbf-ft. (34 to
40 N-m).
Installing the Shoe Cleats
NOTE: The left and right cleats are the same.
1Apply a thin layer of grease on the cleat bolt threads.
2Align the cleat À, washers Á, and bolts Â.
3Use a 4 mm hex key to loosely attach each bolt to the sole of
the shoe.
4Adjust the cleat to the shoe in your preferred position.
This can be adjusted after a trial ride.
5Tighten the cleat firmly to the shoe.
NOTE: Garmin recommends torque of 4 to 6 lbf-ft. (5 to 8 N-
m).
Adjusting the Release Tension
NOTICE
Do not overtighten the release tension screw on the bottom of
the pedal. The release tension should be adjusted equally for
both pedals.
Use a 3 mm hex key to adjust the release tension of each
pedal.
There is a window on the back of the pedal binding that
shows the allowable range.
Paring Vector with Your Edge 1000
Before you can view Vector data on the Edge device, you must
pair the devices.
Pairing is the connecting of ANT+™ wireless sensors. This
procedure contains instructions for the Edge 1000. If you have
another compatible device, see Edge 810 and 510 Device
Instructions, or go to www.garmin.com/vectorowner.
1Bring the Edge device within range (3 m) of the sensor.
NOTE: Stay 10 m away from other ANT+ sensors while
pairing.
2Turn on the Edge device.
2 Introduction
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Garmin Vector at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Garmin Vector in the language / languages: English as an attachment in your email.

The manual is 3,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Garmin Vector

Garmin Vector Quick start guide - English - 26 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info