589619
5
Zoom out
Zoom in
Previous page
1/14
Next page
Introduction
WARNING
Read all instructions carefully before installing and using the
Vector system. Improper use could result in serious injury.
See the Important Safety and Product Information guide in the
product box for product warnings and other important
information.
NOTICE
Go to www.garmin.com/vectorowner for the latest information
including bike compatibility, software updates, and video
tutorials.
Thank You
Thank you for your Vector or Vector S purchase. This manual
covers both Vector systems.
Vector was designed for cyclists, by cyclists, to provide an
outstanding experience of owning a precision power
measurement system for your bike.
Vector is simple, accurate, and easy to use.
For software updates, video tutorials, and everything you need
to get years of service out of your Vector, go to
www.garmin.com/vectorowner.
Now it's time to put the power under your feet and get out there
and ride.
Getting Started
1Install the Vector components (Installing the Vector
Components).
2Install the shoe cleats (Installing the Shoe Cleats).
3Pair Vector with your Edge® (Paring Vector with Your Edge
1000).
4Go for a ride (Your First Ride).
5View your history (Vector Data).
6Send your history to your computer (Sending Your Ride to
Garmin Connect).
Tools Needed
15 mm pedal wrench
Bike grease
3 mm hex key
4 mm hex key
Installing the Vector Components
The installation steps for the Vector and Vector S systems are
very similar. Procedures that are specific to the Vector S system
are noted.
Preparing the Crank Arms
1Confirm the compatibility of your bike at www.garmin.com
/vectorowner.
2Remove the existing pedals.
3Clean the threads, and remove old grease.
Determining Pedal Pod Clearance
NOTICE
The pedal pod should contact the crank arm only at its mounting
face, because this is the load-bearing connection. If the pedal
pod contacts the crank arm anywhere else, the pedal pod may
fracture when the pedal is tightened.
If the mounting face À surrounding the threaded hole in the
crank arm is recessed, use one or two washers Á to fill the
recess.
NOTE: Do not use more than two washers.
Make sure the pedal pod mounting face  contacts the crank
arm only at its mounting face (or the washer used to fill the
recess).
If it touches anywhere else, you can use another washer to
provide the necessary clearance.
If it is close, you can confirm proper clearance by sliding a
piece of paper between the metal bracket and the crank arm
face.
If the mounting face of the crank arm is protruding, do not
use washers.
Determining the Bicycle Chain Clearance
Before you can install the right pedal, you must determine
bicycle chain clearance.
Move your bike chain to the largest chain ring and the
smallest cassette gear.
The bike chain should be in the outermost position to
determine proper clearance between the pedal pod cable
and the chain.
NOTE: There must be at least 5 mm clearance À between
the chain and the crank arm.
Installing the Pedal Pod and Pedal
This procedure is for the Vector system. For the Vector S
system, see Installing the Left Pedal and Pedal Pod.
NOTE: The left and right pedal pods are the same.
1Install the left pedal first.
2Apply a thin layer of grease on the pedal spindle À and the
pedal pod Á where it contacts the pedal spindle.
Introduction 1
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Garmin Vector at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Garmin Vector in the language / languages: English as an attachment in your email.

The manual is 3,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Garmin Vector

Garmin Vector Quick start guide - English - 26 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info