691273
8
Zoom out
Zoom in
Previous page
1/14
Next page
Device Information
Vector Device Care
NOTICE
Keep the components clean and free of debris.
Do not use a sharp object to clean the device.
Avoid chemical cleaners, solvents, and insect repellents that can
damage plastic components and finishes.
Do not submerge or pressure wash the components.
Do not store the device where prolonged exposure to extreme
temperatures can occur, because it can cause permanent
damage.
Replace components with Garmin parts only. See your Garmin
dealer or the Garmin website.
Maintenance Tips
NOTICE
Some bike tools may scratch the finish of Vector components.
Use wax paper or a towel between the tool and the hardware.
After any bike adjustments, rotate the crank arm to check for
clearance.
Keep Vector components clean.
When moving Vector to another bike, clean the threads and
surfaces thoroughly.
Go to www.garmin.com/manuals/vector3 for the latest
updates and information.
Vector Specifications
Battery type User-replaceable LR44 or SR44, 1.5 V, 2 per
pedal
Battery life Up to 120 hr. of riding time, with cycling
dynamics
Operating
temperature range
From -14° to 122°F (from -10° to 50°C)
SR44 batteries may perform better in cold
temperatures.
Wireless
frequencies/
protocols
ANT+ 2.4 GHz @ 3 dBm nominal
Bluetooth
®
2.4 GHz @ 3 dBm nominal
Water rating IEC 60529 IPX7*
*The device withstands incidental exposure to water of up to 1 m
for up to 30 min. For more information, go to www.garmin.com
/waterrating.
Battery Information
The Vector system monitors the battery level of both pedals and
sends status information to your Edge device. When you receive
a low battery warning, you have approximately 10–20 hours of
operation time remaining.
Replacing the Batteries
WARNING
See the Important Safety and Product Information guide in the
product box for product warnings and other important
information.
Each pedal uses two LR44 or SR44, 1.5 V batteries.
NOTE: Garmin recommends replacing all of the batteries at the
same time. Do not mix the battery types.
1
Use a 4 mm hex key to remove the battery cover
À
.
2
Remove the batteries.
3
Wait 5 to 10 seconds.
4
Insert the new batteries into the battery cover, observing
polarity.
5
Replace the battery cover, and hand tighten it.
NOTE: Do not damage or lose the O-ring gasket.
6
Use a 4 mm hex key to gently tighten the battery cover.
NOTE: Do not over-tighten the battery cover. The cover is
sufficiently tight when the O-ring gasket is no longer visible.
The pedal LED flashes red once.
Overhauling the Vector Pedals
You can disassemble and reassemble the pedal spindles to clean and grease the components.
NOTICE
Garmin recommends overhauling one pedal at a time taking care to keep track of the small screws and seals. You must obtain a 4
mm hex key, PH 00 screwdriver, 15 mm pedal wrench, 12 mm socket wrench with an outer diameter that is less than 17 mm
(typically a
1
/
4
in. drive), and bike grease. Use care not to damage any of the Vector components.
NOTE: If you have the Vector 3S system, the right pedal has no battery carriage.
1
Use a 15 mm pedal wrench to remove the pedals.
NOTE: The left pedal spindle has a left-handed (reverse) thread attaching it to the crank arm.
2
Use a 4 mm hex key to remove the battery cover
À
.
4 Device Information
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Garmin Vector 3S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Garmin Vector 3S in the language / languages: English as an attachment in your email.

The manual is 2,24 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Garmin Vector 3S

Garmin Vector 3S User Manual - German - 16 pages

Garmin Vector 3S User Manual - Dutch - 14 pages

Garmin Vector 3S User Manual - French - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info