589622
9
Zoom out
Zoom in
Previous page
1/16
Next page
NOTE: The right pedal has a left-handed (reverse) thread.
3
Remove the pedal body.
4
While securely holding the spindle
Á
with a pedal wrench,
use the 8 mm hex nut driver to remove the nut
Â
and washer
Ã
.
5
Separate the cartridge from the spindle.
6
Remove the brass spacer ring
Ä
and dust seal
Å
.
NOTE: The Vector S right pedal does not include the brass
spacer, and the dust seal is reversed.
7
Remove all old grease from the spindle.
8
Slide the new dust seal and brass spacer ring over the
spindle.
The tapered side of the dust seal and brass spacer ring must
face the base of the spindle.
9
Apply a layer of bike grease to the spindle.
10
Insert the spindle into the cartridge.
11
Wipe away all excess grease.
12
Install the new washer and nut on the end of the spindle.
NOTE: The nut for the right spindle has a left-handed
(reverse) thread.
13
Use the 8 mm hex nut driver to tighten the nut.
WARNING
Garmin recommends torque of 7 lbf-ft. (10 N-m). Failure to
properly tighten the nut could cause the pedal to fall off
during a ride, which could result in property damage or
serious bodily injury or death.
14
Install the new pedal by screwing it onto the cartridge until
there is no gap.
NOTE: The right pedal has a left-handed (reverse) thread.
15
Replace the pedal pods and pedals according to the
installation instructions (Installing the Pedal and Pedal Pod).
16
Rotate the crank arm to check for clearance and smooth
pedal rotation.
After you replace the pedals and cartridges, you must
recalibrate the system.
Vector Storage
If you are transporting your bicycle or not using Vector for an
extended period of time, Garmin recommends removing Vector
and storing it in the product box.
Vector Specifications
Battery type User-replaceable CR2032, 3 volts
Battery life Minimum 175 hours of riding time
NOTE: The pedal pod used on the right crank will
drain the battery faster than the left crank.
Operating
temperature range
From -4° to 122°F (from -20° to 50°C)
Water resistance IPX7
NOTICE
Do not submerge or pressure wash the
components.
Radio frequency/
protocol
2.4 GHz ANT+ wireless communications protocol
USB ANT Stick
Specifications
Power source USB
Operating temperature
range
From 14° to 122°F (from -10° to 50°C)
Radio frequency/protocol 2.4 GHz ANT+ wireless communications
protocol
Transmission range Approximately 16.4 ft. (5 m)
Battery Information
Vector monitors the battery level of both pedal pods and sends
status information to your Edge device. When you receive a low
battery warning, you have approximately 10–20 hours of
operation time remaining.
Replacing the Pedal Pod Battery
WARNING
Do not use a sharp object to remove user-replaceable batteries.
Contact your local waste disposal department to properly
recycle the batteries. Perchlorate Material – special handling
may apply. Go to www.dtsc.ca.gov/hazardouswaste/perchlorate.
NOTE: Always replace both batteries at the same time.
1
Locate the circular battery cover
À
on the back of the pedal
pod.
2
Use a coin
Á
to twist the cover counter-clockwise, moving
the arrow from locked
Â
to unlocked
Ã
.
3
Remove the cover.
You can use a piece of tape
Ä
or a magnet to remove the
battery from the cover.
4
Wait 30 seconds.
5
Insert the new battery into the cover, observing polarity.
NOTE: Do not damage or lose the O-ring gasket.
6
Replace the cover, making sure the arrow points to unlocked.
Device Information 5
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Garmin Vector 2S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Garmin Vector 2S in the language / languages: English as an attachment in your email.

The manual is 2,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info