583791

Garmin TR-1 Gladiator Manual

20
Zoom out
Zoom in
Previous page
1/36
Next page
17
18
To do an outward spiraling search from the waypoint, setup the
special nav function
buttons for search
patterns.
1. Press and hold the [Setup] button on the handheld.
2. Press and light up the [number 9] LED on the handheld.
Release the [Setup] Button.
3. When you are near the waypoint you want to search
from, select “go to” this waypoint on your GPS.
4. With the pilot in heading hold, press and release the [GPS
button] on the handheld, and then press and release one of
the Chevron Buttons. If you pressed the [Right Chevron]
button, the waypoint will remain on your starboard side as
the spiral search unwinds.
Search Pattern
To do an outward spiraling search from a waypoint, setup the special function buttons for search
patterns. (See page 28 Selecting Special Functions) When you are near the waypoint you want
to search from, select go to this waypoint on your GPS. With the pilot in heading hold, press
and release the GPS (Select Load) button and then press and release one of the Bent Arrow
buttons. If you pressed the Bent Right Arrow button, the waypoint will remain on your
starboard side as the spiral search unwinds. The spacing between the spiral laps is set with setup
code 249.
Search Pattern (GPS Steering)
Return to heading hold by pressing one of the straight arrow buttons. An example of the search
pattern is shown in the figure below.
T
o change the setup options for Search Pattern:
You must be in [Auto] or [STBY] mode before selection process can start
1. Press and release
the [Setup] Button. The [Setup] LED will illuminate to indicate the system is
ready to take setup commands (button pushes).
2. Select the Setup Code you want to use by pressing and releasing the buttons labeled 2 &5 until the
appropriate LEDs are lit. (See the Code and Setup Choices on the table below)
3. Increase an adjustable parameter one step by each press of the [UP Arrow] button. When the
parameter is adjusted to its maximum value, the [Up Arrow] LED will light. The parameter is
adjusted and is in use by the autopilot immediately.
4. Decrease an adjustable parameter one step by each press of the [Down Arrow] button. When the
parameter is adjusted to its minimum value, the [Down Arrow] LED will light. The parameter is
adjusted and is in use by the autopilot immediately.
5. To save the changes into permanent memory and make the selected function into a
startup default: Press and release
the [Setup] button (the [Setup] LED should be lit),
and then press and hold
the [Select Load] button. While holding down the [Select Load]
button, press and release the [Deckmount] On/Off button quickly, then release the GPS
[Select Load] button.
Description Code Setup Options (Parameters) Factory Setting
Search Spacing 25 50 to 1,000 ft, by 50 ft. increments 50
… 20 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Garmin TR-1 Gladiator at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Garmin TR-1 Gladiator in the language / languages: English as an attachment in your email.

The manual is 1,68 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info