583791

Garmin TR-1 Gladiator Manual

19
Zoom out
Zoom in
Previous page
1/36
Next page
17
18
Clover Leaf Pattern
The clover leaf pattern is intended for use when you wish to repeatedly
pass over a point where you think sh may be holding.
You will need to setup
the special nav function
buttons (above) for
search patterns.
1. Press and hold [Setup] button on handheld.
2. While holding down the [Setup] button, select and light
up [number 8] LED [Clover] on the handheld. (You will
press the button twice.) Release the Setup button.
3. You must mark the location of the clover leaf stem
with a waypoint in your GPS. Once the waypoint is saved,
select “go to” this waypoint on your GPS.
4. From heading hold, press and release the [GPS button]
on the handheld. The pilot will start maneuvering toward
the waypoint.
If you have selected Clover Leaf pattern as the special function for the Chevron buttons, pressing either
Chevron button will start the boat on the clover leaf pattern. If you used the Right Chevron button the clover
leaf will be traversed by always turning to starboard, the Left Chevron button will cause the pattern to be
traversed while always turning to port. (See Figure 4) The length of one of the clover leaves is programmed
with setup code 28. It is adjustable in length from 500 ft to 6,000 feet in 100 ft. increments. See table below.
Waypoint
Selected on GPS
Right Chevron
Button Pressed
Left Chevron
Button Pressed
Figure 4
Description Code Setup Options (Parameters) Factory Setting
Clover Leaf Length 28 500 to 6,000 ft by 100ft. Increments 1,000
To change the setup options for Clover Leaf:
You must be in [Auto] or [STBY] mode before selection process can start
1. Press and release
the [Setup] Button. The [Setup] LED will illuminate to indicate the system is ready to
take setup commands (button pushes).
2. Select the Setup Code you want to use by pressing and releasing the button labeled 2 & 8 until the
appropriate LED is lit. (See the Code and Setup Choices on the table below).
3. Increase an adjustable parameter one step by each press of the [UP Arrow] button. When the parameter is
adjusted to its maximum value, the [Up Arrow] LED will light. The parameter is adjusted and is in use by the
autopilot immediately.
4. Decrease an adjustable parameter one step by each press of the [Down Arrow] button. When the
parameter is adjusted to its minimum value, the [Down Arrow] LED will light. The parameter is adjusted and
is in use by the autopilot immediately.
5. To save the changes into permanent memory and make the selected function into a
startup default: Press and release
the [Setup] button (the [Setup] LED should be lit),
and then press and hold
the [Select Load] button. While holding down the [Select Load]
button, press and release the [Deckmount] On/Off button quickly, then release the GPS
[Select Load] button.
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Garmin TR-1 Gladiator at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Garmin TR-1 Gladiator in the language / languages: English as an attachment in your email.

The manual is 1,68 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info