579857
101
Zoom out
Zoom in
Previous page
1/412
Next page
190-01007-A3 GTN 6XX/7XX AML STC Installation Manual
Rev. 4 Page 3-21
Prepare all of the shielded cables as shown in Figure 3-3. Refer to Figure 3-5 for details of the shield
termination to the connector backshell. Skip to step 5 below for wires with no shielding.
1. At the end of the shielded cable (11), strip back a 2.5” maximum length of the jacket to expose
the braid. Remove this exposed braid. Carefully score the jacket 1/4” to 5/16” from the end and
remove the jacket to leave the braid exposed.
NOTE
Solder sleeves with pre-installed shield drains should be used instead of separate shield
terminators and individual wires, although separate shield terminators and individual
wires can be used.
2. Connect a 20 or 22 AWG wire (13) to the exposed shield of the prepared cable assembly. (See
Figure 3-2). AC 43.13-1B Chapter 11 may be a helpful reference for termination techniques. Note
that 3 methods are shown in Figure 3-2. The Daisy-Chain method should only be used on P1001
if there are insufficient holes in the shield block to accommodate the shields. Limit the combined
length of the daisy chained shields to 3” maximum.
NOTE
A preferred solder sleeve is the Raychem S03 Series with the thermochromic
temperature indicator. These solder sleeves come with a pre-installed lead and
effectively take the place of items 12 and 13. For detailed instructions on product use,
refer to Raychem installation procedure.
3. Slide a shield terminator (12) onto the prepared cable assembly (11) and connect the wire (13) to
the shield using a heat gun approved for use with solder sleeves. The chosen size of solder sleeve
must accommodate both the number of conductors present in the cable and the wire (13) to be
attached.
4. Repeat steps 1 through 3 as needed for the remaining shielded cables. Note that a maximum of 2
shields can be daisy-chained together.
5. Crimp pins/sockets (14) onto the wires and terminate in the connector (10) in accordance with the
aircraft wiring drawings.
6. For P1001, install the configuration module wires into the connector. Refer to Section 3.6.3.2 for
instructions on installing the configuration module.
101


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Garmin GTN 650 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Garmin GTN 650 in the language / languages: English as an attachment in your email.

The manual is 8,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info