584000
92
Zoom out
Zoom in
Previous page
1/124
Next page
Page 5-10 400 SERIES INSTALLATION MANUAL
Page Rev L P/N 190-00140-02
5.2.11 COM SETUP Page (GNC 420 and GNS 430 Only)
Select the COM SETUP Page (see Figure 5-13). These
values are set at the factory and seldom require calibration.
FREQ
Selects a VHF communication frequency. For purposes of
setting the squelch and sidetone levels, only the
frequencies 118.000, 127.000, and 136.975 MHz can be
used.
SPACING
Selection Description
25.0 kHz
Selects traditional 25 kilohertz spacing (760 channel).
8.33 kHz
Selects 8.33 kilohertz channel spacing, which is required in some areas of the
world.
CAUTION
8.33 kHz channels are not authorized for use in the United States.
SQ 250
Sets the squelch threshold for 25 kHz channel spacing operation. May be set to any value between 0 (zero)
and 63. The higher the number, the less signal is required to break squelch.
NOTE
For GNS 430 units with serial number 200 or lower, the operation of the SQ 250 setting is reversed. The
higher the SQ 250 number, the more signal is required to break squelch.
SQ 833
Sets the squelch threshold for 8.33 kHz channel spacing operation. May be set to any value between 0
(zero) and 63. The higher the number, the more signal is required to break squelch.
SIDE
Sets the sidetone audio output level. May be set to any value between 0 (zero) and 63.
MIC
Sets the Mic Gain output level. May be set to any value between 0 (zero) and 63. This adjusts the output
for differences in microphones used. Should adjustment be necessary refer to the maintenance manual.
This Mic Gain software adjustment is effective for GNS 430 s/n 97107371 and above, and GNC 420 s/n
97202086 and above.
NOTE
The sidetone audio output level is independent of the COM volume knob on the 400 Series unit.
Store Calibration?
Select this field and press the ENT key to accept the squelch threshold and sidetone audio settings on this
page. If you wish for the squelch and sidetone settings to return to their previous values, do not select this
field. Simply change to the next configuration page, or turn off the unit if you are done with configuration.
Selection Verify That:
PTT
The box is filled in while the COM push-to-talk switch is pressed.
XFR
The box is filled in while a remote COM transfer switch is pressed.
RX
The box is filled in while the COM is receiving a signal.
TX
The box is filled in while the COM push-to-talk switch is pressed.
Figure 5-13. COM SETUP Page
92


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Garmin GNC 420 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Garmin GNC 420 in the language / languages: English as an attachment in your email.

The manual is 4,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info