583732
98
Zoom out
Zoom in
Previous page
1/112
Next page
Leg not smoothed - The upcoming leg is too short for smooth
waypoint transitions. Expect a rapid change
in the CDI.
Memory battery low - The battery that sustains user memory is low
and should be replaced by an authorized
GARMIN service center as soon as possible.
Failure to do so may result in loss of stored
data, including all user waypoints and routes.
Near SUA < 2 nm - Your position is within 2 nautical miles of an
SUA, and your current course will not take
you inside.
Need alt - press NAV - The GNC 250 needs altitude input in order
to start and/or continue 2D navigation. Press
the NAV key and enter your antenna altitude
on the Position page. The altitude you enter
should be as accurate as possible. An inaccu-
rate altitude will directly translate into inac-
curate position information.
Offset nav cancelled - Offset navigation has been cancelled due to a
direct-to operation or modification of the
active route.
Offset nav in effect - Offset navigation mode is in effect.
Ofst too big for rte - The parallel track distance is too large for the
active route.
Osc needs adjustment - The GNC 250 has detected excessive drift in its
internal crystal oscillator which may result in
longer acquisition time. The unit should be taken
to an authorized service center immediately.
Poor GPS coverage - The GNC 250 cannot acquire sufficient satel-
lites necessary to provide navigation.
Prox alarm-press NAV - Your craft has penetrated the alarm circle of a
proximity waypoint. Press NAV to see the bearing
and distance to the proximity waypoint.
Proximity overlap - The circles defined by two proximity way-
points overlap. When entering the area of the
overlap, the GNC 250 will warn you of the
closest proximity waypoint, but not both.
You should be certain this condition is
desirable.
Proximity wpt locked - At least one proximity waypoint is locked
because the waypoint has been removed
from the Jeppesen NavData®, the data card
is missing, or the data card has failed.
Proximity wpt moved - One or more proximity waypoints were
moved at least 0.33 arc minutes due to a
database change.
Proximty wpt deleted - One or more proximity waypoints were
deleted while receiving data from the PC
Interface Kit.
Pwr down and re-init - The GNC 250 is unusable until power has
been cycled and the unit re-initialized.
Abnormal satellite conditions may exist.
88
SECTION
D
MESSAGES &
ABBREVIATIONS
250 real 7/14/98 9:33 AM Page 88
98


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Garmin GNC 250 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Garmin GNC 250 in the language / languages: English as an attachment in your email.

The manual is 0,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info