501977

Garmin GHP 12 Autopilot System Manual

9
Zoom out
Zoom in
Previous page
1/28
Next page
GHP12InstallationInstructions 9

To install the CCU, you must mount it to your boat, connect it to the
ECU, connect it to a NMEA 2000 network, and connect it to the alarm
and to the yellow CCU signal wire on the GHC 10.

Before you can mount the CCU, you must select a location and
determine the correct mounting hardware (page 5).
The CCU bracket has two portions, the mounting portion and the
securing portion.
1. Cut out the mounting template provided on page 25.
2. Tape the template to the mounting location.
If you are installing the CCU on a vertical surface, install the
mounting portion of the bracket with an opening
➊
at the bottom.
➊
➋
3. Drill pilot holes at the three mounting locations.
4. Use screws
➋
to secure the mounting portion of the CCU bracket.

1. Connect the CCU/ECU interconnect cable and the NMEA 2000
drop cable to the CCU.
2. Place the CCU in the mounting
portion of the CCU bracket with
the wires hanging straight down
➊
.
3. Place the securing portion of the
bracket over the ball and snap
it it into the mounting portion
of the bracket, starting with the
two arms
➋
that do not have the
thumbscrew
➌
.
4. With the cables hanging straight down, connect the arm with the
thumbscrew.
The cables must hang straight down for the CCU to accurately read
your heading.
5. Hand-tighten the thumbscrew until the CCU is held rmly in the
bracket.
Do not overtighten the thumbscrew.

1. Route the connector-terminated end of the CCU/ECU interconnect
cable to the ECU and make the connection.
2. Route the wires from the bare-wire portion of the cable to the CCU/
ECU interconnect cable.
• Route the red and blue wires to the location where you plan to
install the alarm (page 9).
If the cable is not long enough, extend the appropriate wires with
28 AWG (.08 mm
2
) wire.
• Route the yellow wire to the location where you plan to install
the GHC 10 (page 10).
If the cable is not long enough, extend the yellow wire with 22
AWG (.33 mm
2
) wire.
3. Cut and tape the remaining bare wires; they are not used.

The alarm audibly alerts you to important GHP 12 events. It must be
installed near the helm station.

Before you can mount the alarm, you must select a mounting location
(page 5).
Secure the alarm with cable ties or other appropriate mounting
hardware (not included).

1. Route the alarm-cable to the bare-wire end of the CCU/ECU
interconnect cable.
If the cable is not long enough, extend the appropriate wires with 28
AWG (.08 mm
2
) wire.
2. Connect the cables, based on the table below.




White (+) Red (+)
Black (-) Blue (-)
3. Solder and cover all bare-wire connections.
➊
➋
➌
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Garmin GHP 12 Autopilot System at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Garmin GHP 12 Autopilot System in the language / languages: English as an attachment in your email.

The manual is 2,75 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Garmin GHP 12 Autopilot System

Garmin GHP 12 Autopilot System Installation Guide - Dutch - 10 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info