522219
13
Zoom out
Zoom in
Previous page
1/40
Next page
5
To 10-35 Volt Boat Supply
2A
-
+
Boat Ground
Black Wire
Red Wire
Install 2-Amp
Fuse
To Fishfi nder 250/250C
Installation
Connecting the Power/Data Cable
The power/data cable connects the Fishfi nder 250/250C to a 10-35 volt DC system and provides
interface capabilities for connecting external devices. The color code in the diagram (pg. 6) indicates the
appropriate harness connections. If it is necessary to extend the power/data wires, use a wire of comparable
size and keep your extension as short as possible.
The unit can be wired directly to your boat’s battery or to an unused holder on your boat’s fuse block.
When connecting the unit directly to the battery, make sure the 2-Amp in-line fuse supplied with the unit is
installed . If needed, use an ACG/3AG - 2 Amp replacement fuse. If you decide to use the fuse block, remove
the in-line fuse holder supplied with the unit.
Installing the Wiring Harness (Basic):
1. Determine the polarity of the fuse holder using a Test Light or Volt Meter.
2. Install the Red (+) wire on the Positive Fuse Holder Terminal.
3. Install the Black (-) wire on the Negative Fuse Holder Terminal.
4. Install a 2 amp fuse in the Fuse Holder.
The Fishfi nder 250/250C can be connected to another piece of NMEA compatible electronic equipment,
such as a Garmin GPS (Global Positioning System). If equipped with a capable transducer, the Fishfi nder
250/250C can send depth, temperature, and speed information to the NMEA device. It can also mark a
location (pg. 15) that could be displayed on another device and can accept GPS navigational data (pg. 17),
such as position, time, course, distance, etc. Refer to the wiring diagram on the following page for interfac-
ing the Fishfi nder 250/250C with other devices.
Installing the Wiring Harness to a GPS or other NMEA device:
1. Follow steps 1-4 of the above wiring harness installation. For Garmin units, the Ground (black) wires
from both devices must be attached together or on the same fuse terminal for data ground. Refer to the
wiring diagram of your GPS unit for wire identifi cation.
2. Connect the Blue (Data Out) wire from the Fishfi nder to the Data IN wire on the GPS/NMEA harness.
3. Connect the Brown (Data In) wire from the Fishfi nder to the Data OUT wire on the GPS/NMEA harness.
4. Set the Fishfi nder 250/250C NMEA Input/Output to ‘On’ (pg. 20). For Garmin GPS units, set the
communications interface to NMEA/NMEA, NMEA In/NMEA Out or NMEA.
Wiring and Interfacing
250C Manual.indd 5 1/27/2004, 3:54:56 PM
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Garmin Fishfinder 250C at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Garmin Fishfinder 250C in the language / languages: English as an attachment in your email.

The manual is 1,19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info