522219
12
Zoom out
Zoom in
Previous page
1/40
Next page
4
Installation
Flush Mounting the Fishfi nder 250/250C Unit
The Fishfi nder 250/250C can be fl ush mounted on a fl at panel. When fl ush mounting the Fishfi nder
250/250C, be sure to choose an appropriately sized location for the unit. Check that all cables reach the
unit mounting location before beginning installation. Use the Flush Mount Template provided in the box to
determine a location. Always wear safety goggles and a dust mask when drilling, cutting or sanding.
To ush mount the Fishfi nder 250/250C:
Included Mounting Hardware 4 - 3mm Studs, 4 - Flat Washers, 8 - 3mm Hex Nuts.
Tools (not included) — Center Punch, Drill, 1/8” (3mm) Drill Bit, 3/8” (6mm) Drill Bit, Jig Saw, 1/16”
(2mm) Allen Wrench, 9/35” (7mm) Wrench.
1. Trim the Flush Mount Template and tape in the desired location.
2. Using a Center Punch, indent the center of each Mounting Hole location.
3. Using a 1/8” (3mm) drill bit, drill the four Mounting Holes.
4. Using a 3/8” (6mm) drill bit, drill a hole for a location to begin cutting the mounting surface.
5. Using the Jig Saw, cut the mounting surface along the inside of the dashed line indicated on the
template. Be very careful when cutting this hole, there is only a small amount of clearance
between the unit and the Mounting Holes. It may be prudent to cut slightly inside the indicated
line and then sand or fi le the panel as needed to obtain the best fi t.
6. Install the four Mounting Studs into the unit by screwing the shorter section into the back of the unit.
Use a 1/16” (2mm) Allen Wrench to tighten the Mounting Studs until the stops contact the case. Be
careful not to overtighten as this may damage the Mounting Stud. The studs have a reusable thread-
locking patch pre-applied from the factory.
7. Place the unit in position inside the cutout area of the mounting surface.
8. Place washers over the Mounting Studs, then thread on one Hex Nut per Mounting Stud. Tighten all four
Hex Nuts until the unit is snug against the mounting surface. Install and tighten the second Hex Nut on
all four Mounting Studs to lock the fi rst Hex Nut in place.
Studs
Unit Installation
Washer
Hex Nuts
250C Manual.indd 4 1/27/2004, 3:54:55 PM
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Garmin Fishfinder 250C at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Garmin Fishfinder 250C in the language / languages: English as an attachment in your email.

The manual is 1,19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info