522316
30
Zoom out
Zoom in
Previous page
1/44
Next page
Incoming Distress Calls
If your compatible chartplotter and VHF radio are connected
using NMEA 0183 or NMEA 2000, your chartplotter alerts you
when your VHF radio receives a DSC distress call. If position
information was sent with the distress call, that information is
also available and recorded with the call.
designates a distress call in the DSC list and marks the
position of the vessel on the Navigation chart at the time of the
DSC distress call.
Navigating to a Vessel in Distress
designates a distress call in the DSC list and marks the
position of a vessel on the Navigation chart at the time of the
DSC distress call.
1Select Nav Info > Other Vessels > DSC List.
2Select a position-report call.
3Select Navigate To.
4Select Go To or Route To.
Man-Overboard Distress Calls Initiated from a VHF
Radio
When the chartplotter is connected to a compatible VHF radio
with NMEA 2000, and you initiate a man-overboard DSC
distress call from the radio, the chartplotter shows the man-
overboard screen and prompts you to navigate to the man-
overboard point. If you have a compatible autopilot system
connected to the network, the chartplotter prompts you to start a
Williamson’s turn to the man-overboard point.
If you cancel the man-overboard distress call on the radio, the
chartplotter screen prompting you to activate navigation to the
man-overboard location disappears.
Man-Overboard and SOS Distress Calls Initiated from
the Chartplotter
When your chartplotter is connected to a Garmin NMEA 2000
compatible radio and you mark an SOS or man-overboard
location, the radio shows the Distress Call page so you can
quickly initiate a distress call.
For information on placing distress calls from your radio, see the
VHF radio owner’s manual. For information about marking an
MOB or SOS location, see Marking and Starting Navigation to
an MOB Location.
Position Tracking
When you connect the chartplotter to a VHF radio using NMEA
0183, you can track vessels that send position reports.
This feature is also available with NMEA 2000, when the vessel
sends the correct PGN data (PGN 129808; DSC Call
Information).
Every position report call received is logged in the DSC list
(DSC List).
Viewing a Position Report
1Select Nav Info > Other Vessels > DSC List.
2Select a position-report call.
3Select an option:
To switch to position report details, select .
To switch to a Navigation chart marking the location,
select .
To switch to a Navigation chart marking the location,
select Next Page.
To view the position report details, select Previous Page.
Navigating to a Tracked Vessel
1Select Nav Info > Other Vessels > DSC List.
2Select a position-report call.
3Select Navigate To.
4Select Go To or Route To.
Creating a Waypoint at the Position of a Tracked
Vessel
1Select Nav Info > Other Vessels > DSC List.
2Select a position-report call.
3Select New Waypoint.
Editing Information in a Position Report
1Select Nav Info > Other Vessels > DSC List.
2Select a position-report call.
3Select Edit.
To enter the name of the vessel, select Name.
To select a new symbol, select Symbol, if available.
To enter a comment, select Comment.
To show a trail line for the vessel if your radio is tracking
the position of the vessel, select Trail.
To select a color for the trail line, select Trail Line.
Deleting a Position-Report Call
1Select Nav Info > Other Vessels > DSC List.
2Select a position-report call.
3Select Edit > Clear Report.
Viewing Vessel Trails on the Chart
You can view trails for all tracked vessels on some chart views.
By default, a black line indicates the path of the vessel, a black
dot indicates each previously reported position of a tracked
vessel, and a blue flag indicates the last reported position of the
vessel.
1From a chart or 3D chart view, select Menu > Other Vessels
> DSC Trails.
2Select the number of hours to show tracked vessels on the
chart.
For example, if you select 4 Hours, all trail points that are
less than four hours old appear for all tracked vessels.
Individual Routine Calls
When you connect the chartplotter to a Garmin VHF radio, you
can use the chartplotter interface to set up an individual routine
call.
When setting up an individual routine call from your chartplotter,
you can select the DSC channel on which you want to
communicate. The radio transmits this request with your call.
Selecting a DSC Channel
NOTE: The selection of a DSC channel is limited to those
channels that are available in all frequency bands. The default
channel is 72. If you select a different channel, the chartplotter
uses that channel for subsequent calls until you call using
another channel.
1Select Nav Info > Other Vessels > DSC List.
2Select a vessel or a station to call.
3Select Call with Radio > Channel.
4Select an available channel.
Making an Individual Routine Call
NOTE: When initiating a call from the chartplotter, if the radio
does not have an MMSI number programmed, the radio will not
receive call information.
1Select Nav Info > Other Vessels > DSC List.
2Select a vessel or a station to call.
3Select Call with Radio.
24 Digital Selective Calling
30


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Garmin echoMAP 50 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Garmin echoMAP 50 in the language / languages: English as an attachment in your email.

The manual is 4,91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Garmin echoMAP 50

Garmin echoMAP 50 User Manual - German - 42 pages

Garmin echoMAP 50 Installation Guide - German - 8 pages

Garmin echoMAP 50 Installation Guide - Dutch - 8 pages

Garmin echoMAP 50 User Manual - Dutch - 42 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info