522316
28
Zoom out
Zoom in
Previous page
1/44
Next page
When an engine alarms is triggered, a gauge status alarm
message appears and the gauge may become red depending
on the type of alarm.
Enabling Some Engine Gauge Status Alarms
1From the engine gauges screen, select Menu > Gauge
Setup > Status Alarms > Custom.
2Select one or more engine gauge alarms to turn on or off.
Selecting the Number of Engines Shown in Gauges
You can show information for up to four engines.
1From the engine gauges screen, select Menu > Gauge
Setup > Engine Selection > Num. Engines.
2Select an option:
Select the number of engines.
Select Auto Configure to automatically detect the
number of engines.
Customizing the Engines Shown in Gauges
Before you can customize how the engines are shown in the
gauges, you must manually select the number of engines
(Selecting the Number of Engines Shown in Gauges).
1From the engine gauges screen, select Menu > Gauge
Setup > Engine Selection > Edit Engines.
2Select First Engine.
3Select the engine to display in the first gauge.
4Repeat for the remaining engine bars.
Configuring the Fuel Gauges Display
Before you can configure and display the fuel levels, you must
connect a compatible engine, fuel flow sensor, or tank level
sensor to the NMEA 2000 network.
You can display the total amount of fuel on-board either as a
numeric display that shows the total fuel or as a graphic display
that shows the level in each fuel tank.
1Select Gauges > Engine > Menu > Gauge Setup > Fuel
Display.
2Select an option:
To display the total fuel level in all tanks, select Use Total
Fuel Onboard.
To display the amount of fuel in each tank, select Use
Fuel Tank Levels.
Setting the Fuel Capacity of the Vessel
1Select Settings > My Vessel > Fuel Capacity.
2Enter the combined total capacity of the fuel tanks.
Synchronizing the Fuel Data with the Actual Vessel
Fuel
You can synchronize the fuel levels in the chartplotter with the
actual fuel in the vessel when you add fuel to your vessel.
1Select Gauges > Engine > Menu.
2Select an option:
After you have filled up all the fuel tanks on the vessel,
select Fill Up All Tanks. The fuel level is reset to
maximum capacity.
After you have added less than a full tank of fuel, select
Add Fuel to Boat, and enter the amount added.
To specify the total fuel in the vessel tanks, select Set
Total Fuel Onboard, and enter the total amount of fuel in
the tanks.
Setting the Fuel Alarm
Before you can set a fuel level alarm, a compatible fuel flow
sensor must be connected to the NMEA 2000 network.
You can set an alarm to sound when the total amount of
remaining onboard fuel reaches the level you specify.
1Select Settings > Alarms > Fuel > Fuel Alarm > On.
2Enter the remaining amount of fuel that triggers the alarm.
Viewing the Wind Gauges
Before you can view wind information, you must have a wind
sensor connected to the chartplotter.
Select Gauges > Wind.
Configuring the Sailing Wind Gauge
You can configure the sailing wind gauge to show true or
apparent wind speed and angle.
1From the wind gauge, select Menu > Sailing Wind Gauge.
2Select an option:
To show true or apparent wind angle, select Needle, and
select an option.
To show true or apparent wind speed, select Wind
Speed, and select an option.
Configuring the Speed Source
You can specify whether the vessel speed data displayed on
the gauge and used for wind calculations is based on water
speed or GPS speed.
1From the wind gauge, select Menu > Compass Gauge >
Speed Display.
2Select an option:
To calculate the vessel speed based on data from the
water-speed sensor, select Water Speed.
To calculate the vessel speed based on GPS data, select
GPS Speed.
Configuring the Heading Source of the Wind Gauge
You can specify the source of the heading displayed on the
wind gauge. Magnetic heading is the heading data received
from a heading sensor, and GPS heading is calculated by your
chartplotter GPS (course over ground).
1From the wind gauge, select Menu > Compass Gauge >
Heading Source.
2Select GPS Hdg or Magnetic.
NOTE: When moving at low speeds or when stationary, the
magnetic compass source is more accurate than the GPS
source.
Customizing the Close-Hauled Wind Gauge
You can specify the range of the close-hauled wind gauge for
both the upwind scale and the downwind scale.
1From the wind gauge, select Menu > Compass Gauge >
Set Gauge Type > Close Hauled Gauge.
2Select an option:
To set the maximum and minimum values that appear
when the upwind close-hauled wind gauge appears,
select Change Upwind Scale, and set the angles.
To set the maximum and minimum values that appear
when the downwind close-hauled wind gauge appears,
select Change Downwind Scale, and set the angles.
To view true or apparent wind, select Wind, and select an
option.
Viewing the Environment Gauges
Select Gauges > Environment.
Configuring the Alignment of the Wind Gauge
You can specify the alignment of the wind gauge on the
environment gauges.
1Select Gauges > Environment > Menu > Alignment.
22 Gauges and Almanac Information
28


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Garmin echoMAP 50 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Garmin echoMAP 50 in the language / languages: English as an attachment in your email.

The manual is 4,91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Garmin echoMAP 50

Garmin echoMAP 50 User Manual - German - 42 pages

Garmin echoMAP 50 Installation Guide - German - 8 pages

Garmin echoMAP 50 Installation Guide - Dutch - 8 pages

Garmin echoMAP 50 User Manual - Dutch - 42 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info