463797
5
Zoom out
Zoom in
Previous page
1/6
Next page
echoInstallationInstructions 5

On an echo 200/500c/550c device, the connectors on the cables are keyed to
t only in the correct ports on the cradle. The connected cables are then held
in place by a locking bracket.
No cables connect directly to an echo 200/500c/550c device.
1 Compare the divot
on the cable connector
to the keying on the cradle ports to identify the
correct port.
2. Push the cable connector into the correct port
until it rests rmly in the port.
3. Repeat steps 1 and 2 until all of the
cables are connected to the cradle
.
4. Place the locking bracket
over the
cables and slide it down to lock them
in place on the cradle.
You will hear an audible click when
the locking bracket is correctly
installed.

After you have connected the cables to the cradle, you can quickly place the
echo device in the cradle without plugging in
any cables.
1. Place the base of the echo
in the
bottom of the cradle
.
2. Tilt the echo toward the cradle until it
fastens in place.
You will hear an audible click when the
device is secured in the cradle.


After you have connected the cables to the cradle, you can quickly remove
the echo from the cradle without unplugging any
cables.
1. Press the release lever
on the cradle until
the echo device
is released.
2. Tilt the echo device forward and lift it out of
the cradle.

Notice
Do not leave your boat in the water for an extended period of time without
checking for leaks.
Because water is necessary to carry the sonar signal, the transducer must be
in the water to work properly. You cannot get a depth or distance reading
when out of the water. When you place your boat in the water, check for
leaks around any screw holes that were added below the water line.

Notice
When adjusting the depth of the transducer, make the adjustments in
small increments. Placing the transducer too deep can adversely affect the
performance of the boat and put the transducer at risk of striking underwater
objects.
Test the transom mount transducer installation in open water free of
obstacles. Pay attention to your surroundings as you test the transducer.
1. With the boat in the water, turn on the echo device.
2. Drive the boat at a slow speed. If the echo device appears to be working
properly, gradually increase speed while observing the echo device.
If the sonar signal is suddenly lost or the bottom return is severely
degraded, note the speed at which this occurs.
3. Return the boat to the speed at which the signal was lost, and make
moderate turns in both directions while observing the echo device.
4. If the signal strength improves while turning, adjust the transducer so that
it extends another
1
/
8
in. (3 mm) below the transom of the boat.
5. Repeat steps 2–4 until the degradation is eliminated.
6. If the signal does not improve, move the transducer to a different location
on the transom.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Garmin Echo 300C at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Garmin Echo 300C in the language / languages: English as an attachment in your email.

The manual is 1,71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Garmin Echo 300C

Garmin Echo 300C User Manual - English - 28 pages

Garmin Echo 300C Installation Guide - German - 8 pages

Garmin Echo 300C Quick start guide - German - 24 pages

Garmin Echo 300C Installation Guide - Dutch - 6 pages

Garmin Echo 300C User Manual - Dutch - 28 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info