629013
7
Zoom out
Zoom in
Previous page
1/10
Next page
6
Lower the headrest until the camera is at the desired height.
NOTICE
The headrest must lock into the seat after the camera is
installed. If the headrest does not lock, the camera should not
be installed on this headrest.
Adjusting the Camera Position Using the Extension
Arm Accessory
You can adjust the camera angle and orientation to include the
optimal area in the video frame. You can also adjust the depth of
the extension arm to fit the thickness of your headrest. While
adjusting the camera, it can be helpful to view the video feed
using the
Alignment option in the
babyCam settings on your
navigation device.
To adjust the depth of the extension arm, loosen the clamp
by turning the knob
À
counterclockwise, and rotate the clamp
on the headrest post.
To increase the depth to fit a thicker headrest, rotate the
clamp counterclockwise. To decrease the depth to fit a
thinner headrest, rotate the clamp clockwise.
To level the camera orientation, loosen the threaded ring
Á
by turning it one full turn counterclockwise, and turn the
camera until the subject is level in the video frame.
To point the camera left or right, loosen the thumbscrew near
the clamp
Â
by turning it counterclockwise, and swing the
extension arm left or right.
To point the camera up or down, loosen the thumbscrew
behind the camera
Ã
by turning it counterclockwise, and tilt
the camera up or down.
After you are finished adjusting the camera position, you should
verify the knob, threaded ring, and thumbscrews are fully
tightened.
Adhesive Mount Accessory
The optional adhesive mount accessory allows you to mount the
camera on a window. This can be useful when no headrest post
mounting locations provide a clear view of your passenger. Go
to
garmin.com/babycam to purchase mounting accessories.
Installing the Camera Using the Adhesive Mount
CAUTION
Do not install the camera in a location that interferes with the
driver's view of the road or environment.
NOTICE
Do not install the adhesive mount on a window that can roll
down. Rolling down a window with the adhesive mount installed
can result in damage to the mount, camera, window assembly,
or window motor.
1
Clean the window using water or alcohol, and a lint-free cloth.
The window must be free of dust, wax, oils, or coatings.
2
Remove the protective film from the mount adhesive.
3
Position the mount over the mounting location.
TIP:
The adhesive is extremely sticky. Do not touch the
adhesive to the window until the mount is properly positioned
and aligned.
4
Press the mount firmly onto the window, and maintain
pressure for 30 seconds.
5
Wait
24 hours before installing the camera.
The adhesive takes 24 hours to bond properly to the window.
6
After 24 hours, place the camera onto the mount and secure
it with a thumbscrew.
Removing the Adhesive Mount
The adhesive mount is intended for a long-term installation and
can be difficult to remove.
1
Firmly grip the mount.
2
Pull the mount up and away from the window or surface,
applying steady pressure until the adhesive releases.
3
Remove all remaining adhesive from the surface.
Receiver Cable
Your compatible Garmin
navigation device receives a video
signal from the
babyCam camera using the receiver cable
included with the camera. To view video from the camera, you
must power your navigation device using this cable. If your
navigation device and camera were purchased separately, the
receiver cable replaces the power cable originally included with
your navigation device.
Installation 3
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Garmin BabyCam at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Garmin BabyCam in the language / languages: English as an attachment in your email.

The manual is 1,02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Garmin BabyCam

Garmin BabyCam User Manual - German - 12 pages

Garmin BabyCam User Manual - Dutch - 12 pages

Garmin BabyCam User Manual - French - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info