501979
6
Zoom out
Zoom in
Previous page
1/12
Next page
6 AIS 600 Instructions
If the AIS 600 is wired to a non-Garmin NMEA 0183 chartplotter, or not wired to a chartplotter at all, then you must install a toggle switch
to turn the device on and off.
Connect the yellow wire from the AIS 600 power/data cable to one terminal of a single-pole, single-throw switch (not included), and
connect the other terminal to the negative (-) battery terminal.
When you close the switch, the AIS 600 powers on. When you open the switch, the AIS 600 powers off.
Installing the GA 38 GPS Antenna
You must install the included GA 38 GPS antenna and connect it to the AIS 600 according to the following instructions. The AIS 600 will not
transmit a signal unless the GA 38 is installed properly and receiving a satellite signal.
The AIS 600 does not accept GPS information from any other GPS device or antenna on the boat. Also, the AIS 600 does not share GPS
information from the GA 38 antenna with any other device on the boat.
You can surface mount the GA 38 antenna or attach the antenna to a standard 1 in. OD (14 threads per inch) pipe-threaded-pole marine mount
(not included).
Select a suitable location for the GA 38 antenna on your boat. To ensure the best reception, mount the GA 38 antenna in a location with a clear
view of the sky in all directions.
Avoid mounting the GA 38 antenna in the shade of the superstructure of the boat, a radome
antenna, or a mast.
Mount the GA 38 antenna at least 3 ft. (1 m) away from (preferably above) the path of
any radar beam or a VHF radio antenna.
Temporarily secure the antenna in the preferred mounting location and test it for correct
operation. If you experience interference from other electronics, try a different location. When
you verify correct operation, permanently mount the antenna.
Surface-mounting the GA 38 Antenna
1 Use the surface-mount bracket as a mounting template.
Use a center punch to mark the three screw locations on the surface.
Use a pencil to trace the cable hole in the center of the bracket.
Set the surface-mount bracket aside. Do not drill through the surface-mount bracket.
2. Drill
1
/
8
in. (3 mm) pilot holes at the three marked locations.
NOTE: If you are mounting the GA 38 on berglass, it is recommended that you
use a countersink bit to drill a clearance counterbore through the top gelcoat layer
(but no deeper). This will help to prevent cracking in the gelcoat layer when the
screws are tightened.
3. Use a 1 in. (25 mm) hole saw to cut the cable hole in the center.
4. Place the seal pad on the bottom of the surface-mount bracket. Ensure that the
screw holes align.
5. Use the included M4 screws to attach the surface-mount bracket to the mounting
surface.
6. Route the cable through the 1 in. (25 mm) cable hole and connect it to the GA 38.
7. Ensure that the large rubber gasket is in place on the bottom of the GA 38
antenna, place the antenna on the surface-mount bracket
, and twist the
antenna clockwise to lock it in place
.
8. Secure the antenna to the mounting bracket with the included M3 set screw
.
9. Route the cable away from sources of electronic interference, and connect it to the
AIS 600 using the BNC connector.
Radar
SS BARNETT
VHF Radio Antenna
Above - best
Below - OK
3 ft.
(1 m)
EMI (Electromagnetic Interference)
from engine components
Best
Better
Good
EMI
GA 38 Antenna Placement Considerations
GA 38
antenna
Surface-mount
bracket
Mounting
surface
Rubber
gasket
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Garmin AIS 600 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Garmin AIS 600 in the language / languages: English as an attachment in your email.

The manual is 1,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Garmin AIS 600

Garmin AIS 600 User Manual - German - 12 pages

Garmin AIS 600 User Manual - Dutch - 12 pages

Garmin AIS 600 User Manual - French - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info