501979
5
Zoom out
Zoom in
Previous page
1/12
Next page
AIS 600 Instructions 5
Installing the AIS 600
Use the following instructions to install the AIS 600 device. Details for the following steps are included in this document:
1. Select locations for the AIS components.
2. Mount the AIS 600 transceiver box.
3. Wire the AIS 600 to power.
4. Install and connect the GA 38 GPS antenna (page 6).
5. Connect the AIS 600 to a VHF antenna and to an optional VHF radio (page 7).
6. Connect the AIS 600 to a NMEA 2000 network or to a NMEA 0183-compatible chartplotter (optional - page 7).
7. Add a silent-mode switch or a Safety Related Message (SRM) switch (optional - page 8).
Selecting Locations for the AIS 600 Components
Use the wiring layout diagrams starting on page 3 to determine how to best organize the AIS 600 components on your boat. Ensure that the
cables reach all components before permanently mounting any component.
Mounting the AIS 600 Transceiver Box
Install the AIS 600 transceiver box below deck on a bulkhead. Select a location that is dry and protected from washdown. Ensure that the
location is well ventilated and away from objects that generate heat. Ensure that the transceiver box is at least 15
3
/
4
in. (40 cm) from any
compass to avoid interference.
Needed Tools
Drill and drill bits
Number 2 Phillips screwdriver
To mount the transceiver box:
1. Ensure that the chosen location is dry, protected, and well-ventilated.
2. Use the transceiver box as a template, and use a pencil to mark the holes in the four corners. Do not drill through the transceiver box.
3. Drill four
1
/
8
in. (3 mm) pilot holes.
4. Mount the transceiver box using the included M4.2 × 25 screws. You can also use bolts, washers, and nuts (not included) to mount the
transceiver box if the mounting surface is suitable.
Connecting the Transceiver Box to Power
Use the AIS 600 power/data cable to connect the transceiver box to a 12 or 24
Vdc battery.
Notes:
Use the AIS 600 Power Wiring-Assignment Table to identify the positive and
negative wires.
The replacement fuse on the power/data wiring harness is a 5 A, fast-acting fuse.
If it is necessary to extend the power wires, use 16 AWG or larger wire.
Installing the AIS 600 Power Toggle
The AIS 600 can be powered on and off in one of 3 ways:
If the AIS 600 is connected to a NMEA 2000 network, it will toggle on and off with the NMEA 2000 network.
NOTE: The AIS 600 is not powered by the NMEA 2000 network, although it will turn on when it detects power on the NMEA 2000
network. You must connect the AIS 600 to power, and not just to the NMEA 2000 network.
If the AIS 600 is wired to a Garmin chartplotter using NMEA 0183, connect the yellow wire from the AIS 600 power/data cable to the
Accessory On wire from the chartplotter. The AIS 600 will then toggle on or off with the Garmin chartplotter.
Device Wire Color Function
AIS 600 power/data
cable
Red Power—positive (+)
Black Ground—negative (-)
AIS 600 Power Wiring-Assignment Table
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Garmin AIS 600 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Garmin AIS 600 in the language / languages: English as an attachment in your email.

The manual is 1,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Garmin AIS 600

Garmin AIS 600 User Manual - German - 12 pages

Garmin AIS 600 User Manual - Dutch - 12 pages

Garmin AIS 600 User Manual - French - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info