Manual Gardol GEM-E 1742 (page 25 of 160) (English, German, Dutch, French, Italian, Polish, Spanish)

724419

Zoom out

Zoom in

1/160

- 25 -

To take oﬀ the grass basket, use one hand to lift

up the chute ﬂ ap and the other to grab onto the

basket handle. Remove the basket. For safety

reasons, the chute ﬂ ap automatically falls down

after removing the grass basket and closes oﬀ the

rear chute opening. If any grass remains in the

opening, it will be easier to restart the engine if

you pull the mower back approximately 1m.

Do not use your hands or feet to remove clippings

in or on the mower housing, but instead use suita-

ble tools such as a brush or a hand broom.

In order to ensure that the majority of grass clip-

pings are picked up, the inside of both the grass

basket and especially the net must be cleaned

after each use.

Reattach the grass basket only when the motor is

switched oﬀ and the blade has stopped.

Lift up the chute ﬂ ap with one hand and, holding

the grass basket by its handle with the other

hand, hang in the basket from the top.

7. Replacing the power cable

Danger!

If the power cable for this equipment is damaged,

it must be replaced by the manufacturer or its

after-sales service or similarly trained personnel

to avoid danger.

8. Cleaning, maintenance and

ordering of spare parts

Danger!

Always pull out the mains power plug before star-

ting any cleaning work.

8.1 Cleaning

•

Keep all safety devices, air vents and the

motor housing free of dirt and dust as far as

possible. Wipe the equipment with a clean

cloth or blow it with compressed air at low

pressure.

•

We recommend that you clean the device

immediately each time you have finished

using it.

•

Clean the equipment regularly with a moist

cloth and some soft soap. Do not use

cleaning agents or solvents; these could at-

tack the plastic parts of the equipment. Ensu-

re that no water can seep into the device. The

ingress of water into an electric tool increases

the risk of an electric shock.

8.2 Carbon brushes

In case of excessive sparking, have the carbon

brushes checked only by a qualiﬁ ed electrician.

Danger! The carbon brushes should not be rep

laced by anyone but a qualiﬁ ed electrician.

8.3 Maintenance

•

Worn out or damaged blades, blade mounts,

and bolts should be replaced as a set by an

authorized professional in order to keep the

equipment in balance.

•

Do not clean the lawn mower with running

water, particularly with high-pressure water.

Ensure that all mounting components (i.e.

screws, bolts, nuts etc.) are always tightened

so that the equipment can be safely operated

at all times.

•

Frequently check the grass catch assembly

for signs of wear.

•

Replace excessively worn or damaged parts

immediately.

•

Store your lawn mower in a dry room.

•

In order to ensure that you enjoy the equip-

ment for many years to come, all screwed

parts, as well as the wheels and axles, should

be cleaned and lubricated.

•

Keeping your lawn mower in good condition

not only ensures a long lifespan and high per-

formance, but also enables the equipment to

thoroughly cut your grass with minimal effort.

For best results, clean the lawn mower with a

brush or rag. Do not use any solvents or water

to remove dirt.

•

The blade is subjected to more wear and

tear than any other component. Therefore,

routinely check the condition of the blade

and make sure that it is tightly fastened. If the

blade is completely worn out, it must be im-

mediately replaced or ground sharp again. An

excessively vibrating mower means that the

blade is not properly balanced or has become

deformed from striking an object. In this case,

the blade must be repaired or replaced.

•

There are no parts inside the equipment

which require additional maintenance.

Anl_GEM_E_1742_SPK7-1.indb 25Anl_GEM_E_1742_SPK7-1.indb 25 26.11.2019 06:24:2626.11.2019 06:24:26

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Gardol GEM-E 1742 in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 2,37 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Gardol GEM-E 1742 Manual

Product: