Manual Gardol GEM-E 1742 (page 23 of 160) (English, German, Dutch, French, Italian, Polish, Spanish)

724419

Zoom out

Zoom in

1/160

- 23 -

Fitting the wheels (Fig. 3a and b)

Take a rear wheel (Fig. 2/Item 11) and push it

onto the axle as shown in Fig. 3a. Then slide a

washer (Fig. 2/Item 15) onto the axle and fasten

all parts with the supplied split pin (Fig. 2/Item 14)

as shown in Fig. 3a. Finally, press the wheel cap

(Fig. 2/Item 12) onto the wheel as shown in Fig.

3b. Proceed in exactly the same way on the other

side.

Mounting the push bar (Fig. 4 to 7).

Mount a bottom push bar (Fig. 2/Item 2) onto the

screw provided for it and secure everything with

a wing nut (Fig. 2/Item 13) as shown in Fig. 4.

Proceed in the same way on the other side. When

you ﬁ t the top push bar you can decide the height

of the push bar by selecting the appropriate fas-

tening hole (Fig. 5). Finally, secure the top push

bar to the bottom push bar as shown in Fig. 6.

Now you can attach the motor cable to the push

bar (Fig. 7/Item A) using the cable clips (Fig. 2/

Item 16).

Mounting the grass basket

(see Figs. 8a and b)

Press the grass box handle (Fig. 8a/Item 21)

into the grass basket as shown in Fig. 8a. Before

you ﬁ t the grass basket you must ensure that the

motor is switched oﬀ and the blade is not rotating.

Lift the ejector ﬂ ap (Fig. 8b/Item 3) with one hand.

With the other hand, hold the grass basket by the

handle and hook it in from above (Fig. 8b).

Filling level indicator of the grass collector

The grass collector is equipped with a ﬁ lling level

indicator (Fig. 1/Item 7) which is opened by the

airﬂ ow that the lawn mower generates during ope-

ration. If the ﬂ ap closes during mowing, the grass

collecting device is full and must be emptied. To

ensure the proper functioning of the ﬁ lling level

indicator, the holes under the ﬂ ap must always be

kept clean and passable.

Adjusting the cutting height

Important!

Adjust the cutting height only when the motor is

switched oﬀ and the power cable has been dis-

connected.

Before you begin to mow, check to ensure that the

blade is not blunt and that none of the fasteners

are damaged. To prevent any imbalance, replace

blunt and/or damaged blades. To carry out this

check, ﬁ rst switch oﬀ the motor and pull out the

power plug.

The cutting height is adjusted as follows

(see Fig. 9):

1. Push the lever inwards.

2. Set the lever to the desired cutting height.

3. Release the lever and check that it is securely

seated in the lock.

Reading oﬀ the cutting height

The cutting height can be set between 20-65 mm

in 6 intervals, and can be read oﬀ on the scale.

Power supply

The lawn mower can be connected to any light

socket-outlet with a 230-240 Volt alternating

current. However, the socket outlet must have an

earthing contact protected by a 16 A circuit brea-

ker. Additionally, a residual current device (RCD)

circuit-breaker with max. 30 mA must be used!

Power cable for the device

Please only use power cables that are not dama-

ged. The total length of the power cable should

not exceed 50 meters; going beyond this distance

will reduce the power output of the electric motor.

The power cable must have a cross-section of

3 x 1,5 mm

. The insulating sheath of lawn aerator

power cables is frequently damaged.

Some of the causes for this are:

•

Cuts caused by driving over the cable.

•

Pinching when the power cable is dragged

under doors and pulled through windows.

•

Cracking due to old age of the insulation.

•

Kinking by improperly fastening or guiding the

power cable.

The power cables must, at the very minimum, be

of type HO5RN-F and 3-stranded. The cable type

must be printed somewhere on the power cable.

Only purchase power cables that are marked!

Plugs and socket couplers for the power cables

must be made from rubber and splash-proof.

There is a limit to how long power cables can be.

Longer power cables require larger conductor

cross-sections. Power cables and connecting li-

nes must be regularly checked for damage. Ensu-

re that the lines are switched oﬀ before checking

them. Completely unwind the power cable. Also

check power cable entry points, plugs and socket

couplers for kinks.

Anl_GEM_E_1742_SPK7-1.indb 23Anl_GEM_E_1742_SPK7-1.indb 23 26.11.2019 06:24:2626.11.2019 06:24:26

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Gardol GEM-E 1742 in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 2,37 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Gardol GEM-E 1742 Manual

Product: