724631

Gardenline XKJ1109 Manual

12
Zoom out
Zoom in
Previous page
1/21
Next page
1100W Garden Pump
AFTER SALES SUPPORT
e-mail: info.aldi@positecgroup.com
1300 889 028
MODEL: №. XKJ-1109PE • 1/2019 • 44268
(toll free)
AFTER SALES SUPPORT
(toll free)
1100W Garden Pump
e-mail: info.aldi@positecgroup.com1300 889 028
MODEL: №. XKJ-1109PE • 1/2019 • 44268
20 21
Connecting to the intake port (6) (Where water is to be
transferred from)
The Intake connection is to be connected to your
water supply via various connections (not supplied).
An example set up is shown here (Fig Q).
The intake port (6) of the pump is 1” BSP.  So to
purchases of any ttings for the intake port (6) of
the pump, the threaded tting is required to be
1” BSP. This is shown as number 6 on page 8.
For the intake port (6), purchased ttings can be
used directly into the intake port (6) of the pump.
The tting supplied which is not being used on the pressure outlet (5) can
be used on the intake port (6) if required, however it is critical one of the
supplied ttings is used into the pressure outlet (5) of the pump.
Extra ttings can also be purchased from our online spare parts store.
Description NOTE: Teon tape (not supplied) is applied to all ttings
requiring tape for correct assembly.
Connecting the intake hose / suction pipe.
1. Screw an intake hose* minimum of 19mm (3/4”) diameter hose preferably
spiral re-inforced. This may be directly, or with a threaded nipple to the
pump’s intake port (6) (25 mm (R1) (1” BSP)).
2. The intake hose* should rise from the water pick-up point up to the
pump. Always avoid laying the intake line higher than the pump as
this will cause air bubbles in the intake line which will delay and hinder
suction (Refer previous Fig C).
3. The intake and pressure lines* must be attached in such a way that they
do not place the pump under any mechanical strain.
4. If the intake line* is not air-tight the intake of air will hinder the intake
of water.
Purchased components for plumbed inlet: 
Figures R & S show the components for the plumbed threaded inlet
for a non pressure connection.
The tting supplied which is not being used on the pressure outlet (5) can be
used on the intake port
(6) if required, HOWEVER,
it is critical one of the
supplied adaptor ttings
(10 & 11) is used into the
pressure outlet of the
pump (5).
Preparing your pump for operation for the rst use.
NOTE: Ensure the unit is NOT connected to the mains power when
undertaking this task (Fig A).
NOTE: During the priming process if your pump is connected to a tap, ensure
the tap is open (Fig T).
Once the preparation of the pump is complete, you are ready to prime the
pump.
Preparing to prime your Garden Pump
The objective/process of priming your pump is to remove air from the system.
1. Set up the pump on at and rm ground (refer Fig C).
2. Using the spanner (8), unscrew the clear water ller cap (1) (Fig U) and
remove the coarse lter (2) together with the non-return valve (3) (Fig V/W).
NOTE: If the lter and
non-return valve does
not lift out of the pump,
remove the water intake
screw (7) (Fig X) and
gently push the non
return valve (3) upward
using the end of the
supplied spanner (8)
(Fig Y).
Q.
R. S.
T. U.
LOOSEN
OPEN
CLOSE
TIGHTEN
* Additional ttings are NOT supplied with this garden pump.
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gardenline XKJ1109 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gardenline XKJ1109 in the language / languages: English as an attachment in your email.

The manual is 1,07 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info