724641

Gardenline PM2006H Manual

13
Zoom out
Zoom in
Previous page
1/21
Next page
45cc Petrol Chainsaw
AFTER SALES SUPPORT
e-mail: help@powertoolsupport.com
1800 909 909
MODEL: №. 53942 • 09/2018 • PM2006H
(toll free)
AFTER SALES SUPPORT
(toll free)
e-mail: help@powertoolsupport.com1800 909 909
45cc Petrol Chainsaw
MODEL: №. 53942 • 09/2018 • PM2006H
22 23
Stopping the Chainsaw
1. Release the throttle trigger (3).
2. Press down the on/o switch (4) to the “STOP”
position (Fig AC).
NOTE: Especially after the rst starting of the
chainsaw, the tension of the chain should be
checked. The chain will become loose on the rst
start up and will require adjustment. Refer to the
“Changing / Replacing the Guide Bar and Chain”
section.
Checking the Oil supply
Run the engine at medium speed and check that
the chain splatters a thin line of oil which can be
seen on the ground when the guide bar (19) is
pointed downwards (Fig AD). DO NOT ALLOW THE
TIP OF THE BAR touch ANY surface when checking
the oil ow. Keep the chain (20) and guide bar (19)
well clear of ANY surface. This visual thin line of oil
is normal and is an indication the oil system is oiling
the guide bar (19) and chain (20).
NOTE: For rst time use the oil may take a few
minutes to work through the oil system.
The oil pump is ONLY operating while the chain (20)
is rotating so at idle the oil is NOT being pumped
through the oil system. If there is no line of chain oil
after a few minutes, stop the engine immediately
and investigate the cause. The oil tank (6) could be empty or the oil supply
to the chain blocked. This may require removal of the guide bar (19) and
checking that the upper oil hole in the bar is clear of any blockages (Fig AE).
Adjusting the Carburettor
NOTE: It is recommended the carburettor adjustment is performed by a
service centre to ensure the correct setting for both safety and performance.
The carburettor is factory set and should not require adjustment.
6 . Hold the chainsaw securely on the ground by
placing one foot on the rear handle, one hand
secure on the front handle, and using your other
hand, slowly pull the recoil starter (11) 2 times so
that air and fuel is drawn into the engine slowly
(Fig AA).
7. Push the combination choke control / throttle lock
knob (10) back inwards (As now the engine has
been primed).
8. Again hold the chainsaw securely on the ground
by placing one foot on the rear handle, one hand
secure on the front handle, and using your other
hand pull at a steady and medium rate on the
recoil starter (11) (Fig AA).
9. Pull the throttle trigger upward to release the
throttle lock (this is engaged when you pull the
combination choke control / throttle lock knob (10) on).
10. To start cutting, release the front guard / chain brake (13), by pulling it
rmly towards the back of the chainsaw until a click is heard (Fig Y).
11. Press in the safety lever (2) then the throttle trigger (3), to commence
movement of the chain and start cutting (Fig AB).
Warm / Hot Starting the Chainsaw
Follow this procedure when starting the chainsaw if you have recently
stopped it and wish to restart it or have had to refuel or add oil etc.
1. Turn the on/o switch (4) to the “On” position as indicated by an “I” (Fig X).
2. Make sure the front guard / chain brake (13) is ON when starting for safety
by pushing it rmly towards the nose of the chainsaw bar until a click is
heard (Fig Y). This ensures the chain wont start spinning upon starting.
3. Press the priming bulb (36) 4 times or until the priming bulb (36) is full of
fuel.
4. Hold the chainsaw securely on the ground, by placing one foot on the rear
handle, one hand securing the front handle, and using your other hand,
pull at a steady and medium rate on the recoil starter (Fig AA).
AD.
AC.
AE.
Operation Operation
AB.
AA .
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gardenline PM2006H at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gardenline PM2006H in the language / languages: English as an attachment in your email.

The manual is 2,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info