724644
11
Zoom out
Zoom in
Previous page
1/20
Next page
47.1cc Petrol Chainsaw
AFTER SALES SUPPORT
e-mail: help@powertoolsupport.com
1800 909 909
MODEL: №. 61705 • 08/2018 • FCS4800A
(toll free)
AFTER SALES SUPPORT
(toll free)
e-mail: help@powertoolsupport.com1800 909 909
47.1cc Petrol Chainsaw
MODEL: №. 61705 • 08/2018 • FCS4800A
18 19
5. Secure fuel tank cap (9) nger tight, and then using the oil tank cap (7),
secure the fuel tank cap (9). ENSURE you wipe any residue from around the
fuel tank cap (9).
6. It is important to now ll the combination oil tank (6) with 4 stroke engine
oil per following instructions.
NOTE: Should you lose the oil tank cap (7), an additional oil tank cap (7) has
been supplied with this chainsaw
Adding 4 Stroke Oil to the Chainsaw
WARNING: Always ensure the engine is turned o before
undertaking this task.
WARNING: Never start work unless the chain (20) and guide bar (19)
are lubricated.
NOTE TO CHECK: Always ensure the combination oil tank (6) is full of 4 stroke
engine oil each time the chainsaw is being used.
1. Using a funnel, ll the oil tank (6) with 260ml of quality 4 stroke oil, or to just
under the lip of the oil tank opening. (Fig S).
2. Fasten the combination oil tank cap (7), and if there is any spillages, ensure
you clean with a clean rag.
Preparation Operation
Operation
WARNING: Do not start the engine whilst the chainsaw hangs from one
hand. This is very dangerous as the chain (20) may come in contact with your
body and the starting action is not controlled .
NOTE: This chainsaw is tted with an easy start recoil starter (11).
This means the recoil starter only needs to be pulled at a steady medium rate
and not hard vigorous pulling.
1. Fill the fuel and oil tanks respectively per
previous instructions and ensure both caps are
secure. Remove the bar cover (31).
2. Press in the priming bulb (5) up to 10 times, or
until the priming bulb (5) is rm and full of fuel,
when the chainsaw is cold or being used for the
rst time, or after the chainsaw has previously
run out of fuel (Fig T).
4. Press the on/o switch (4) to the “On position, as marked with an “I (Fig
U). For safety when starting, make sure the front guard / chain brake (13) is
on by pushing it rmly towards the nose of the chainsaw bar until a click is
heard (Fig V).
5. When the machine is cold, or the chainsaw has previously run out of fuel,
pull out the choke control (10) to the fully extended position (Fig W).
6. Hold the chainsaw securely on the ground by
placing one foot on the rear handle, one hand
securing the front handle. Using your other
hand, pull at a steady and medium rate on the
recoil starter (11) (Fig X).
7. Repeat until the engine res, and then STOP as
soon as the engine kicks (attempts to start) or
runs in any way.
8. Push the choke control (10) back in (Fig Y).
9. Pull the recoil starter (11) again and restart the
engine. Allow the engine to warm up.
10. When ready to start cutting, release the front
guard / chain brake (13), by pulling it rmly
towards the back of the chainsaw until a click is
heard (Fig A).
U. V. W.
X.
Y.
FULLY
EXTEND
X 10
T.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gardenline FCS4800A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gardenline FCS4800A in the language / languages: English as an attachment in your email.

The manual is 1,94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info