724644
8
Zoom out
Zoom in
Previous page
1/20
Next page
47.1cc Petrol Chainsaw
AFTER SALES SUPPORT
e-mail: help@powertoolsupport.com
1800 909 909
MODEL: №. 61705 • 08/2018 • FCS4800A
(toll free)
AFTER SALES SUPPORT
(toll free)
e-mail: help@powertoolsupport.com1800 909 909
47.1cc Petrol Chainsaw
MODEL: №. 61705 • 08/2018 • FCS4800A
12 13
This chainsaw comes fully assembled in the box and does not require any
pre-assembly.
Replacing/Re-Installing the Guide Bar & Chain
WARNING: The chain has sharp edges.
Use work gloves for safety.
WARNING: Ensure the engine is switched o when making any
adjustments to the chain and bar.
IMPORTANT: The front guard / chain brake (13) must be disengaged
when replacing / reinstalling the guide bar (19) and/or chain (20).
1. Place the chainsaw on a at and secure
surface and check that the chain brake (13) is
disengaged (Fig A).
2. Remove the chain drive side cover (23) by using
the combination tool (bar nut tube spanner)
(32) in an anti-clockwise direction to loosen
the chain drive side cover nuts (24). (Fig B), and
then remove the chain drive side cover (23).
Ensure the chain brake (13) is NOT engaged.
3. With the chainsaw on its side and the bar uppermost, (Fig C), push the
guide bar (19) towards the drive sprocket (29) (Fig D), which will result in
the chain (20) loosening around the guide bar (19).
4. Remove the chain (20) from the guide bar (19) starting at the nose of the
guide bar rst. Once the chain (20) is removed from the guide bar (19),
the slack chain can be removed o the main drive sprocket and lifted over
the brake and clutch assembly (22). The guide bar (19) is then removed
by sliding it away from the chainsaw housing and then lifting the bar over
the two threaded studs. When the bar is removed from the chainsaw it
should be thoroughly cleaned of sawdust and oil prior to reassembly.
5. Insert the guide bar (19) into position over the 2 threaded studs, and on
a slight angle upwards, and push the guide bar (19) under the clutch and
brake assembly (22) fully towards the drive sprocket (29) to easily place
the chain (20) around the guide bar (19) (Fig E).
6. Place the new chain over and then under the chain brake and clutch
assembly (22), and then around the drive sprocket (29) loosely with the
chain links in the direction shown on the guide bar (19) (Fig F).
Important Information Assembly
A.
BRAKE
OFF
Assembly
IMPORTANT INFORMATION
B. D.C.
LOOSEN
FLAT
NOTE: SIDE VIEW
E.
F .
This chainsaw uses a 4 stroke engine and does not require the
mixing of oil with the fuel.
The chainsaw is tted with ONE oil tank which supplies oil to
BOTH the engine and also the chain and bar.
4 Stroke Engine oil is required to be added to the combination oil
tank (6) on this chainsaw.
ALWAYS ll the combination oil tank (6) with 4 stroke oil every
time fuel is added to the fuel tank (8).
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gardenline FCS4800A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gardenline FCS4800A in the language / languages: English as an attachment in your email.

The manual is 1,94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info