782039
32
Zoom out
Zoom in
Previous page
1/53
Next page
m A new saw chain stretches, requiring adjustment after as few as 5 cuts. This is
normal with a new chain, and the interval between future adjustments will lengthen
quickly.
m If the saw chain is TOO LOOSE or TOO TAUT, the drive wheel, chain bar, chain and
crank shaft bearing will suffer premature wear. Fig. 4/pos. X2 shows the correct tension
(when cold) and Fig. 4/pos. X3 shows the tension (when warm). Fig. 4/pos. X1 shows a
chain that is too loose.
3. CHAIN BRAKE MECHANICAL TEST
Your chainsaw is equipped with a chain brake that reduces the possibility of injury due
to kickback. The brake is activated if pressure is applied against the brake lever when,
as in the event of kickback, the operator's hand strikes the lever. When the brake is
actuated, chain movement stops abruptly.
m WARNING
The purpose of the chain brake is to reduce the possibility of injury due to kickback;
however, it cannot provide the intended measure of protection if the saw is operated
carelessly. Always test the chain brake before using your saw and periodically while on
the job. (See below for details of how to perform a test of the mechanical brake).
4. TO TEST CHAIN BRAKE
The chain brake is DISENGAGED (chain can move) when the BRAKE LEVER (5) IS
PULLED BACK (Fig. 11/pos. 2) AND LOCKED shown in Fig. 11.
The chain brake is ENGAGED (the chain is locked) when the brake lever (5) is pulled
forward and the mechanism (shown in Fig. 10) can be seen. It should not be possible
to move the chain (Fig. 30).
m WARNING
The brake lever should snap into both positions. If strong resistance is felt, or the lever
does not move into either position, do not use your saw. Take it immediately to a
professional Service Centre for repair.
5. FUEL AND OIL – RECOMMENDED FUELS
Use only a mixture of unleaded petrol and special 2-stroke engine oil. Mix the fuel
mixture as indicated in the fuel mixing table.
36 AFTER SALES SUPPORT
aldi.service.uk@scheppach.com 00800 4003 4003
MODEL: CSP41 PRODUCT CODE: 64055 04/2017
Set up Petrol chainsaw 41cc
32


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gardenline CSP41 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gardenline CSP41 in the language / languages: English as an attachment in your email.

The manual is 6.97 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info