724632

Gardenline 50752 Manual

12
Zoom out
Zoom in
Previous page
1/16
Next page
Understanding and using these operating instructions
1200W Lawn Edger
AFTER SALES SUPPORT
e-mail: help@powertoolsupport.com
1800 909 909
MODEL: №. 50752 • 11/2018 • 50752
(toll free)
Operating instructions and safety notes!
AFTER SALES SUPPORT
(toll free)
1200W Lawn Edger
e-mail: help@powertoolsupport.com1800 909 909
MODEL: №. 50752 • 11/2018 • 50752
20 21
Changing the Blade
WARNING: Ensure the edger is switched o and is disconnected from
mains power before undertaking this task.
1. Loosen and remove the guard lock knob (15) and open the blade guard
(14). (Fig U/V)
2. Place the supplied blade spanner (24) over the outer blade ange (18) to
hold it in position, and then use a 14mm spanner (not included) to remove
the blade lock nut (17) in an anti-clockwise direction. (Fig X)
3. Remove the blade lock nut (17), outer blade ange (18) and the 190mm
serrated blade (16), and ensure the spindle and inner ange (19) are clean of
any dirt, etc. (Fig Y)
4. Fit the new 190mm serrated blade (16) then the outer blade ange (18),
then the blade lock nut (17). Using the supplied blade spanner (24) to hold
the outer blade ange in position, tighten the blade lock nut (17) using a
14mm spanner in a clockwise direction. (Fig X)
5. When the 190mm serrated blade (16) is secure, rotate it by hand to ensure
the blade is not making contact with any components of the edger. (Fig Z)
6. Close the blade guard (14), and nger tighten the guard lock knob (15). (Fig U)
NOTE: Blade wear is expected whenever you use your edger. Blades wear
quite quickly when edging along concrete paths. This does not aect the
eciency of the edger and is expected due to the aggressive abrasion of
concrete on steel.
Blades should be replaced when they become worn and no longer edge the
grass cleanly.
Replacement blades are available for purchase from our website
https://help.tools/ or by calling 1800 909 909.
X. Y. Z.
TIGHTEN
LOOSEN
Maintenance
NOTE: This product is not suitable for repair or maintenance work by the
unskilled person. The following detail explains how the blade is changed,
how the product is cleaned, and basic maintenance / safety checks. All other
maintenance work must be carried out by service agents who are experienced
with both the mechanical and electrical aspects of this product.
Safety / Deterioration Check
Any of the following faults found should be investigated and repaired by a
qualied service agent or a similarly qualied person in order to avoid hazard:
• Prior to each use or during the cleaning operation check the following with
the 240V ac mains power DISCONNECTED from the product.
• Check the guard is rmly mounted and the swing door locates, closes and
locks correctly.
• Check the guard is not cracked or fractured.
The following checks should be made with the 240V ac mains supply
connected:
• BE AWARE and take precautions as the blade will rotate under some of the
checks. Tests should be made on soft ground with the blade clear of the
ground.
• Gently depress the trigger switch (2) without the safety lock button (3)
being depressed. The product should not start. (Do Not use the product if
the unit starts without the safety lock button (3) not pressed).
• Press the safety lock button (3) and the trigger switch (2) to start the edger.
Release the trigger switch (2). The unit MUST stop. If the unit fails to stop,
remove the plug from the 240V ac mains supply. (DO NOT use the product
in this condition).
• On start up, the motor and the blade rotation should be an even growling
noise. If there is a grinding, or squealing noise, or uneven speed, turn o the
edger, disconnect and have the unit serviced by a qualied service agent or
a similarly qualied person in order to avoid hazard.
The following faults, if found, can be corrected by the owner of the edger,
unless the fault requires disassembly, which must be performed by a qualied
service agent or a similarly qualied person in order to avoid hazard.
• Check the wheels freely turn without binding.
• Check the height adjustment is fully located and rmly clamped by the
height adjustment knob (21).
• Check there is no build up of grass around the spindle.
• Check the blade size and cutting edge of the blade. Replace the blade if
necessary per the instructions to follow.
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gardenline 50752 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gardenline 50752 in the language / languages: English as an attachment in your email.

The manual is 0,79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info