724632

Gardenline 50752 Manual

11
Zoom out
Zoom in
Previous page
1/16
Next page
Understanding and using these operating instructions
1200W Lawn Edger
AFTER SALES SUPPORT
e-mail: help@powertoolsupport.com
1800 909 909
MODEL: №. 50752 • 11/2018 • 50752
(toll free)
Operating instructions and safety notes!
AFTER SALES SUPPORT
(toll free)
1200W Lawn Edger
e-mail: help@powertoolsupport.com1800 909 909
MODEL: №. 50752 • 11/2018 • 50752
18 19
Landscaping / Trenching
Before landscaping or trenching, inspect and ensure there are no exposed or
buried cables or pipes or other objects that may create a hazard or interfere
with operating the edger. Lift the edge guide (23) for all trenching. Set the
depth to only that required for the job. Do not overload. If the edger slows,
pull back slightly and wait until the blade returns to normal speed.
Cleaning the Guard Chamber
WARNING: Ensure the edger is switched o and is disconnected from
mains power before undertaking this task.
After each use the blade guard chamber should be cleared of dirt and grass
build-up, to maintain cutting eciency.
1. Undo the guard lock knob (15) and open the blade guard (14). (Fig U/V)
2. Use a stick or screw driver to clean all debris build up in the guard chamber.
(Fig W)
3. When the debris are removed, close the blade guard (14) and ensure the
guard lock knob (15) is tightened.
NOTE: Edging of heavily overgrown edges and damp soils can create
greater build-up of dicult to remove waste. It may be necessary to remove
the bulk of this material using a long thin implement (ie. screwdriver).
U. V. W.
TIGHTEN
LOOSEN
Edging
1. Set the cut depth at 24mm and set edge guide
lever (12) to the down position.
2. The guard incorporates a raised rib section which
acts as a blade cut indicator. This rib will assist in
guiding the operator where the blade will cut.
(Fig S). During operation the operator can sight
down the rib of the guard to where the edge is
to be cut.
3. Before starting the edger, line up the edger so
the edge guide (23) rests against the edge of the
paved surface. Both rear wheels should be on
the paved surface when edging.
NOTE: When there is heavy overgrowth of grass
over the paved surface it may drag on the guard.
An initial cut may be required with the edger on
the grass side. This will require lifting up the edge
guide (23) and may require reducing the depth
of cut.
4. To avoid kickback of the edger, tilt the handle down so the blade is above
the ground. (Fig T)
5. Turn the edger on and allow the blade to spin without moving the edger.
6. Slowly raise the handle to lower the blade, nding the edge of the paved
surface and start edging. Then move forward slowly along the edge of the
paved surface, keeping the edge guide (23) pressed lightly against the
pavement edge.
Edging Tips:
- For the rst edging each season, it is best to move forward slowly as grass
is thickest then. Subsequent edging will be completed more rapidly.
- If the edger slows down, back it up slightly until the blade returns to
normal speed.
- During edging some sparks may be generated from hitting stones: this
is normal. Do not attempt to edge when the grass or soil is wet or moist;
both for electrical safety and to prevent clogging of the blade chamber.
S.
T.
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gardenline 50752 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gardenline 50752 in the language / languages: English as an attachment in your email.

The manual is 0,79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info