687471
39
Zoom out
Zoom in
Previous page
1/56
Next page
24 h
A
B
Mowing
Charging
Standby
Operation
GARDENA R130Li, R130LiC
Operation, A = max. hours 19
Charging/Standby, B = min. hours 5
4.7.4 Example 2
The times used in this example are applicable to
GARDENA R130Li, R130LiC, but the principle is the
same for the other models.
Timer setting Period 1 (A): 00:00 - 18:00.
Timer setting Period 2 (C): 20:00 - 23:00.
Active period (A): 00:00 - 16:00
Active period (C): 20:00 - 21:00.
The robotic lawnmower will operate between 00:00 and
18:00. It will begin again at 20:00 but stops running at
21:00 due to standby mode until it starts again at 00:00.
Mowing
Charging
Operation
Operation
Standby
S
t
and
by
GARDENA R130Li, R130LiC
Operation, A + C = max. hours 19
Charging/Standby, B + D = min. hours 5
4.8 Charge a flat battery
When the GARDENA robotic lawnmower is new or has
been stored for a long period, the battery will be flat and
needs to be charged before starting.
WARNING: Only charge the robotic lawnmower
using a charging station which is intended for it.
Incorrect use may result in electric shock,
overheating or leakage of corrosive liquid from
the battery.
In the event of leakage of electrolyte flush with
water and seek medical help if it comes in
contact with the eyes etc.
1. Set the main switch to position
1
.
2. Place the robotic lawnmower in the charging station.
Open the hatch and slide the robotic lawnmower in
as far as possible to ensure proper contact between
the robotic lawnmower and the charging station. See
contact and charging strips in
Product overview on
page 5
3. The display shows a message that charging is in
progress.
4.9 Adjust the cutting height
The cutting height can be varied from MIN (2 cm) to
MAX (6 cm).
If the grass is long, let the robotic lawnmower to start
mowing at the MAX cutting height. Once the grass is
shorter, you can gradually lower the cutting height.
4.9.1 To adjust the cutting height
1. Press the STOP button to stop the robotic
lawnmower.
2. Open the cutting height adjustment hatch.
3. Turn the knob to the required position.
Turn clockwise to increase the cutting height.
Turn counter-clockwise to decrease the cutting
height.
4. Close the hatch.
CAUTION: During the first week after a new
installation, the cutting height must be set to
MAX to avoid damaging the loop wire. After this,
the cutting height can be lowered step by step
every week until the desired cutting height has
been reached.
307 - 002 - 11.10.2017 Operation - 39
39


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gardena Smart SILENO R100LiC - 2018 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gardena Smart SILENO R100LiC - 2018 in the language / languages: English as an attachment in your email.

The manual is 7,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Gardena Smart SILENO R100LiC - 2018

Gardena Smart SILENO R100LiC - 2018 User Manual - German - 64 pages

Gardena Smart SILENO R100LiC - 2018 User Manual - Dutch - 60 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info