687475

Gardena smart SILENO plus R160LiC 2018 Manual

27
Zoom out
Zoom in
Previous page
1/56
Next page
Area 1, 2 or 3
How?
How far?
How often?
Disable
More
Lawn coverage
The factory settings allow the robotic lawnmower to
follow the guide wire 300 m in 20% of the times it leaves
the charging station. If the guide wire in reality is less
than 300 m the robotic lawnmower will follow it to the
point where the guide wire is connected to the boundary
wire.
3.16.1.1 Area 1, 2 or 3 > How?
The robotic lawnmower uses the Guide to reach Area 1,
2 or 3. If all areas will be used it is therefore important to
consider the optimal placement of the charging station.
The Guide needs to pass all areas but at the same time
not exceed maximum length of guide wire.
3.16.1.2 Area 1, 2 or 3 > How far?
Enter the distance in metres along the current wire from
the charging station to the remote area where the
robotic lawnmower begins mowing.
Use the right and left arrow keys to alternate between
the different options.
Tip! Use the
Test
function (
Area 1, 2 or 3 > More >
Test
) to determine how far it is to the remote area. The
distance, stated in metres, will be shown in the
lawnmower display when STOP has been pressed. See
How to measure the distance to a remote area on page
28
. The measured distance shown in the display can
be saved directly to the selected remote area. Any
current value will be overidden by the new measured
distance.
? m / ft.
3.16.1.3 Area 1, 2 or 3 > How often?
How often the robotic lawnmower must be steered to the
remote area is selected as a proportion of the total
number of times it leaves the charging station. At all
other times, the robotic lawnmower starts to mow at the
charging station.
Select the percentage that corresponds to the size of the
remote area relative to the total working area. If the
remote area is for instance half of the total working area,
50% must be selected. A lower figure must be specified
if the remote area is smaller. If more areas are used,
take into account that the total figure cannot exceed
100%.
Compare with the examples in
Yard layout examples on
page 33
.
Use the number keys to specify share as a percentage.
30%
20%
3.16.1.4 Area 1, 2 or 3 > Disable
Each area can be disabled and enabled without having
to reenter the settings. Select
Disable
and press OK.
3.16.1.5 Area 1, 2 or 3 > More > Test
Testing selected settings can be seen as a natural part
of the installation.
Using the
Test
function, the robotic lawnmower travels
the farthest distance from the guide wire allowed by the
selected corridor width.
3.16.1.6 Test: Area 1, 2 or 3
To test the selected settings:
1. Place the robotic lawnmower in the charging station.
2. Use the down and the right/left arrow keys to select
the area to be tested from the
Lawn coverage
overview
screen. Press OK.
3. Select
More
and press OK.
4. Select
Test
and press OK.
5. Press START and close the hatch.
6. The robotic lawnmower will now leave the charging
station and begin following the guide wire toward the
remote area. Check that the robotic lawnmower can
follow the guide wire all along the required distance.
7. The test is approved when the robotic lawnmower
can follow the guide wire to the required starting
point without any problem.
307 - 002 - 11.10.2017 Installation - 27
… 27 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gardena smart SILENO plus R160LiC 2018 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gardena smart SILENO plus R160LiC 2018 in the language / languages: English as an attachment in your email.

The manual is 7,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Gardena smart SILENO plus R160LiC 2018

Gardena smart SILENO plus R160LiC 2018 User Manual - German - 64 pages

Gardena smart SILENO plus R160LiC 2018 User Manual - Dutch - 60 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info