672952

Gardena Smart City Sileno 500 - 2018 Manual

26
Zoom out
Zoom in
Previous page
1/56
Next page
2. Select
New loop signal
in the menu.
3. Press OK and await confirmation that the loop signal
has been generated. This normally takes about 10
seconds.
Change PIN code
1. Enter the current PIN code by using the up/down
arrow keys and press OK.
2. Enter the new PIN code and press OK.
3. Confirm by entering the same code again and press
OK.
When the PIN code is changed, the message
PIN code
changed
appears in the display. Make a note of the new
PIN code on the designated line in Memo. See
Introduction on page 3
.
3.14.2 Lawn coverage
This menu function is used to steer the robotic
lawnmower to remote parts of a working area. In
complex gardens with for instance many areas which
are joined by narrow passages, the mowing result can
be much improved by changing settings.
Note: The lawn coverage function is enabled after a
successful guide calibration. See
Guide calibration on
page 20
.
Up to 3 remote areas can be set. Select an area using
the left and right arrow keys followed by OK.
Area 1
Area 3
Area 2
A number of unique selections are required to allow the
robotic lawnmower to reach the remote area.
Area 1, 2 or 3
How?
How far?
How often?
Disable
More
Lawn coverage
The factory settings allow the robotic lawnmower to
follow the guide wire 99 m in 20% of the times it leaves
the charging station. If the guide wire in reality is less
than 99 m the robotic lawnmower will follow it to the
point where the guide wire is connected to the boundary
wire.
3.14.2.1 Area 1, 2 or 3 > How?
The robotic lawnmower uses the Guide to reach Area 1,
2 or 3. If all areas will be used it is therefore important to
consider the optimal placement of the charging station.
The Guide needs to pass all areas but at the same time
not exceed maximum length of guide wire.
3.14.2.2 Area 1, 2 or 3 > How far?
The robotic lawnmower stops following the guide wire
and starts mowing at a specified distance from the
charging station. Up to 3 different distances can be set.
Tip! Use the
Test
function (
Area 1, 2 or 3 > More >
Test
) to determine how far it is to the remote area. The
distance, stated in metres, will be shown in the
lawnmower display when STOP has been pressed. See
How to measure the distance to a remote area on page
27
. The measured distance shown in the display can
be saved directly to the selected remote area. The
current value will be overidden by the new measured
distance.
? m / ft.
3.14.2.3 Area 1, 2 or 3 > How often?
How often the robotic lawnmower should be steered to
the remote area is selected as a proportion of the total
number of times it leaves the charging station. At all
other times, the robotic lawnmower starts to mow at the
charging station.
Select the percentage that corresponds to the size of the
remote area relative to the total working area. If the
remote area is for instance half of the total working area,
50% must be selected. A lower figure must be specified
if the remote area is smaller. If more areas are used,
take into account that the total figure cannot exceed
100%. Compare with the examples in
Yard layout
examples on page 32
.
26 - Installation 367 - 004 - 16.02.2018
… 26 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gardena Smart City Sileno 500 - 2018 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gardena Smart City Sileno 500 - 2018 in the language / languages: English as an attachment in your email.

The manual is 8,66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Gardena Smart City Sileno 500 - 2018

Gardena Smart City Sileno 500 - 2018 Quick start guide - English - 4 pages

Gardena Smart City Sileno 500 - 2018 Quick start guide - German - 4 pages

Gardena Smart City Sileno 500 - 2018 User Manual - German - 60 pages

Gardena Smart City Sileno 500 - 2018 Quick start guide - Dutch - 4 pages

Gardena Smart City Sileno 500 - 2018 User Manual - Dutch - 60 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info