474442

Gardena CSI 4020-X-8863 Manual

18
Zoom out
Zoom in
Previous page
1/21
Next page
ENGLISH - 8
Cutting action pushing the chain (from bottom to top)
(fig.3) will lead to the danger of a sudden movement of
the machine in the direction of the user, with the risk of
hitting the user, or an impact of the “kickback danger
zone” on the trunk resulting in strong kickback; extreme
care must be taken when cutting in this manner.
The safest method for using the machine, is to block the
log on a sawhorse, cutting from top to bottom, on the
portion outside the sawhorse. (fig.4)
Spiked bumper use.
Where possible, use the spiked bumper to ensure safer
cutting action: plant it in the bark or surface of the trunk in
order to maintain more control over the machine.
Below are descriptions of typical cutting procedure to be
adopted for specific situations. However, these should be
assessed each time to calculate whether the method is
most suitable or not, In order to use a method with the
least possible risk.
Trunk on the ground. (Risk of touching the ground with
the chain once the bar has passed trough the trunk).
(fig.5)
Cut from top to bottom through the whole trunk. Towards
the end of the cut, proceed very carefully to prevent the
chain from hitting the ground. If it is possible, cut 2/3 of
the trunk, roll it over, and cut the remaining third from top
to bottom to limit the risk of the chain touching the
ground.
Trunk supported at one end only (Risk of trunk
breaking during cutting action). (fig.6)
Begin the cut from underneath for about 1/3 of the
diameter, and then finish the cutting action from the top to
meet the undercut.
Trunk supported at both ends. (Risk of pinching the
chain). (fig.7)
Begin the cut from above for about 1/3 of the diameter,
and then continue from underneath to meet the overcut.
Trunk laying on a slope. Always stand on the uphill side
of the log. When ʻcutting throughʼ, to maintain complete
control, release the cutting pressure near the end of the
cut without relaxing your grip on the chainsaw handles.
Do not let the chain contact the ground.
Tree felling.
ATTENTION!: Never attempt to fell a tree if you do not
have the necessary experience, and in any case never
fell trees that have trunks with a diameter larger than the
length of the bar! This operation is reserved for expert
machine users with adequate equipment.
When felling a tree, the aim is to have the tree fall in the
most convenient position for the following limbing and
bucking operations. (Avoid trees falling on top of other
trees: Felling trees that are entangled with other trees is
a very dangerous operation).
First of all decide which is the best direction for the tree to
fall by evaluating the following: objects or other plants
around the tree, the inclination, the curve, wind direction,
and greatest branch concentration. Take into account
dead or broken branches that may break off during felling
creating a further danger risk.
ATTENTION! During tree felling operations in critical
conditions, always remove ear protection immediately
after cutting operations to be able to listen for unusual
noises and any warning signals.
Preliminary cutting operations and identifying the
retreat path.
Eliminate any branches that interfere with the job (fig.8),
starting from top to bottom, and then, always keeping the
trunk between the user and the machine eliminate the
more difficult branches afterwards, piece by piece.
Eliminate all plants that interfere with work operations and
control the area for possible obstacles (rocks, roots,
ditches,etc.) when planning the retreat path (to follow
during tree fall); Refer to the illustration (fig.9) for the
directions to be maintained (A. predicted tree fall
direction. B. Retreat path. C. Danger zone).
FELLING CUTS (fig.10)
In order to ensure that the user has complete control over
the tree fall, the cutting instructions are as follows:
The cut that controls the fall direction of the tree is to be
executed first: First of all cut the UPPER PART of the
directional notch on the side the tree must fall. Remain
on the right hand side of the tree and cut using the chain
pull method; then cut the LOWER PART that must meet
the end of the upper part. The depth of the directional
notch must be 1/4of the trunk diameter, with an angle of at
least 45° between upper and lower cut. The meeting
point between the two sides of the notch is called
“directional cut line” This line must be perfectly horizontal
at right angles (90°) to the felling direction.
The felling cut that provokes the tree fall, is performed at
3 to 5cm above the lower part of the directional felling cut
line, finishing at a distance of 1/10 of the trunk from the
notch. Remain on the left hand side of the tree and cut
using the chain pulling method and the spiked bumper.
Check that the tree does not move in a direction other
than that predicted for the fall. As soon as possible insert
a felling lever or wedge into the cut. The uncut part of the
trunk is called the “hinge”, as it is intended to guide the
tree as it falls; in cases where the cuts are not sufficient,
not straight, or have been cut through completely, the tree
fall cannot be controlled (extremely dangerous!). For this
reason the various cuts must be performed with great
precision.
When cutting operations are completed the tree will begin
to fall. Where necessary help tree fall using wedges or
felling levers.
Limbing
Once the tree has been felled, the trunk must be limbed:
in other words, the branches are removed from the trunk.
Do not underestimate this operation because the large
majority of kickback accidents occur during this stage.
For this reason pay close attention to the position of the
bar nose during cutting operations and always work on
the left hand side of the trunk.
… 18 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gardena CSI 4020-X-8863 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gardena CSI 4020-X-8863 in the language / languages: English as an attachment in your email.

The manual is 7.69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Gardena CSI 4020-X-8863

Gardena CSI 4020-X-8863 User Manual - German - 21 pages

Gardena CSI 4020-X-8863 User Manual - Dutch - 21 pages

Gardena CSI 4020-X-8863 User Manual - French - 21 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info